Toilet Flange Too Low? Why Stacking Wax Rings Fails
Toilet flange too low? I would check the height and bolt support first, then choose a spacer, a repair ring or one thicker seal for the actual problem. [1]
As an Amazon Associate I earn from qualifying purchases. How this site earns
Written by: Isaac Daniels, Licensed Journeyman Plumber (JP507711)
In my 7 years of experience, these are the products I'd install.
Updated November 15, 2026
Eastman 40145. Amazon listing photo.
The short answer
A low flange can leave an incomplete seal. Oatey recommends a flange on top of or even with the finished floor. For a buried flange, correct the height with a compatible spacer or extension kit; for a sound flush flange, one jumbo ring can work. [1]
This finder cannot replace an in-person inspection. Stop using a leaking toilet if the floor is soft or the flange moves; have the supporting structure and drain connection inspected before resetting it. [1]
Picks by need
Eastman 40145 jumbo wax ring
For a sound flange even with the finished floor. I would raise a buried flange before choosing the seal. [1]
Buy it if the flange is secure and flush with the floor. Skip it if the flange is below the floor or damaged. The tradeoff is that wax must be replaced whenever the bowl is lifted. [1]
Amazon listing photo. Listed thickness: 1¼ inches. Fits 3 or 4 inch waste lines. [5]
A spacer or extension kit corrects height; a repair ring restores bolt support. I would measure and inspect before buying either. Those are repair paths, rather than additional product picks here. [3]
A flange can start at the correct height when a house is built. Then someone laid tile, or LVP, or a second layer of underlayment over the original floor, and did not touch the flange. For example, adding thicker flooring raises the finished surface while an unchanged flange stays at its original height. Now it is buried. [2]
This is why the problem shows up as “the toilet was fine until I redid the bathroom.” The toilet did not change. The floor did. [2]
The other route to the same place is a corroded cast iron or steel flange in an older house, where the ring has rusted down and the bolt ears have broken off. Same symptom, different repair. [2]
What actually goes wrong when the flange is too low
The wax ring is a compression seal. It must compress between the toilet outlet and the flange to form a seal. Set the flange too deep and the ring may not make complete contact, Oatey’s guidance on a low flange is blunt about the consequence: “The wax ring may not seal properly.” [1]
Check for these symptoms before choosing a repair: [2]
1A smell that comes and goes. Sewer gas escaping past an incomplete seal. Check the flange seal as well as other possible odor sources. [2]
2A rocking toilet, though that comes from the wrong fix rather than from the depth itself. Stacked seals can compress unevenly or shift. A flange that is too high can also make the toilet rock, stressing the seal. [4]
3Water at the base after a flush, often only a few drops, often only sometimes, which is exactly why it goes unnoticed until the subfloor is soft. See a toilet leaking at the base for the full symptom list. [2]
The slow version of this is the expensive one. A seal that weeps a little with every flush rots the subfloor from above, so inspect the supporting floor for damage before resetting the bowl. A soft floor needs repair before it can securely support the flange fasteners. [2]
The mistake: stacking two wax rings
This is a wrong answer to a low flange, and it is worth being direct about. [4]
Two stacked rings do not compress as one. The layers can compress unevenly, fail to mold together and shift, leaving a gap for water or sewer gas. Adding wax does not correct a loose flange or an uneven base. Movement can break the seal, so I would correct the support and flange position before fitting one appropriate ring. [4]
If your toilet rocks but the base is still dry, start with how to fix a wobbly toilet: snug bolts and shims come before pulling anything up. [2]
I would use one ring and correct the flange height rather than rely on a stack of separate wax seals. A seal can leak below the bowl before water becomes visible, so check the floor and the ceiling below for dampness before treating this as a simple reset. [4]
Use one ring, and change the flange height instead. [4]
The right fixes, in order
1. Flange is level with the floor → jumbo wax ring
This is a legitimate, manufacturer-supported answer. Oatey state it directly: “if the flange is even with the finished floor, you can use a jumbo or MaxWax® ring to achieve a secure, watertight seal.” One thicker ring, not two standard ones. I would still check the bowl clearance and the condition of the flange before choosing this repair. See the best toilet wax rings, for a comparison of wax and wax-free options and their fit requirements. [1]
2. Flange is below the floor → spacer or extension kit
This is the actual repair for a buried flange. Oatey’s guidance: “If the flange sits too low, use a flange spacer or extension kit such as the Oatey® Set-Rite® Toilet Flange Spacer System to raise it to the correct height.” [3]
Follow the exact spacer or extension kit instructions for sealing and fastening. Oatey distinguishes solvent-welded PVC spacers or a silicone seal between layers from complete extension kits; the sealing method is not interchangeable across every product. Measure the gap from the top of the flange to the finished floor first and buy for that dimension, this is a measure-once job, and guessing means a second trip. [3]
3. Bolt ears broken or flange corroded → repair ring
A repair ring (sometimes called a half-moon or flange repair plate) is a metal ring that goes over the damaged flange and gives you fresh bolt slots. It fixes broken ears; it does not fix height. If the flange is both broken and buried, you need the repair ring and the height corrected. [3]
4. Everything is wrong → replace the flange
Replacement is the repair when the existing flange cannot be made sound. The replacement method depends on the pipe material and connection. Some repair flanges use an internal gasket; other installations require removal of the existing connection. On PVC the pipe condition and access matter; on cast iron it is a bigger job and a reasonable place to call somebody. My walkthrough of replacing a toilet covers the reset either way. [3]
If the bowl also has to move sideways, because it sits too close to the wall or fouls the vanity, that is a horizontal problem and a different part: see my offset toilet flange picks. [3]
Fasten it to the subfloor, not the finish floor
Whatever you do about height, the flange has to be anchored properly or the whole repair moves. Oatey’s guidance is to “always use rust-proof screws to anchor the flange to the subfloor,” and to match the hardware to what you are anchoring into, “Concrete: Use concrete anchors. Wood: Use wood screws.” [1]
Screwing a flange into a half-inch of tile or vinyl alone gives you a flange that lifts under load. The screws need to reach structure. [1]
Before you put the toilet back
1Dry-fit it. Set the toilet with no wax and check that it sits flat on the floor and does not rock. Fix the rock now, not after the wax is committed. [2]
2Shim if needed, then trim the shims. A toilet that rocks will break its seal no matter how good the flange height is. [2]
3Set it once. Lower it straight down and do not twist it into place, twisting smears the wax and opens a leak path. [2]
4Do not overtighten the closet bolts. Snug, alternating side to side. Overtightening can crack porcelain. [2]
Fresh wax every time the toilet comes up, without exception. A used ring will not re-compress. Full detail in how to replace a toilet wax ring. [2]
The part that fixes it
1Eastman 40145 jumbo wax ring with flange, 1-1/4 inches thick per the listing; one jumbo ring is the fix when the flange sits even with the finished floor. Below the floor, raise the flange instead. [5]
A wax-free seal needs its own flange-height and drain-size compatibility check. I would not use a generic wax-free recommendation to avoid correcting a buried or loose flange. Compare the seal options in the wax ring guide. [2]
FAQ
How high should a toilet flange be?
Oatey state that “the flange should sit on top of or even with the finished floor.” On top is ideal; even with the floor is workable using a thicker wax ring. Below the finished floor is the condition that causes leaks and needs correcting with a spacer or extension kit. [1]
Can I use two wax rings if my flange is too low?
I would not stack rings. Oatey warns that stacked layers can compress unevenly and shift, leaving gaps that allow leaks or sewer gas. Use one jumbo ring if the flange is level with the floor, or raise the flange properly if it is below. [4]
What do I use if the flange is below the finished floor?
A flange spacer or extension kit. Oatey’s guidance is to “use a flange spacer or extension kit such as the Oatey® Set-Rite® Toilet Flange Spacer System to raise it to the correct height.” Measure the gap from the top of the flange to the finished floor before buying so you get the right stack height. [1]
Why does my toilet rock even after a new wax ring?
Check whether the bowl rocks without a seal. If it rocks dry, inspect the floor and use appropriate shims on a sound surface. If it only rocks with a seal in place, check seal thickness and flange clearance. A loose flange also needs anchoring before the toilet goes back. [2]
Does a flange repair ring fix a low flange?
No. A repair ring restores broken bolt ears on a damaged flange; it does not raise the flange to the correct height. If the flange is both broken and too low, you need the repair ring plus a spacer, or a full flange replacement. [3]
I kept the Eastman 40145 from this guide and checked its model, dimensions, product photo and New offer against the Amazon listing on November 15, 2026. I used Oatey's flange installation guidance to separate height correction from seal selection. A ring intended for a flush flange is not my fix for a loose or buried flange.
The Fluidmaster 7530P8 and Korky kit remain comparisons in the linked seal guide, rather than additional picks here. Compatibility has to be checked for the exact seal and flange position.