Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
What a plumber drills with a rotary hammer
A rotary hammer hits the bit while it turns, and takes SDS bits made for concrete. These are the jobs it covers on plumbing work.
Hanger anchors overhead
Drop-in anchors for 3/8 in. rod take a 1/2 in. bit, per Simpson Strong-Tie. They're behind a lot of hanger rod.
Core holes for pipe
Holes through a wall or slab for pipe. Makita and Bosch list core bit sizes up to 3-1/8 in. and 2-5/8 in.
Chipping slab
Chip mode breaks out concrete for a floor drain, a toilet flange or a trench for a new line.
Strap and clip anchors
Small holes in block and concrete for pipe straps and clips. A light hammer is easier here.
Drilling steel and wood
In rotation-only mode, with a chuck adapter, some hammers drill steel and wood. Bosch lists sizes for both on the 11255VSR.
Cores bigger than 3-1/8 in.
No maker here lists a core size above 3-1/8 in. For 4 in. pipe, use a core drill rig.
Prices and availability are accurate as of the time shown and may change.
Pros
DEWALT lists rod hanging and clip mounting
Brushless motor
2.6 J of impact energy
Side handle and depth rod included, per the listing
Sold by Amazon.com
Cons
Blows per minute not listed
No hole-size range or core size listed
Battery and charger sold separately
1 in. class, SDS-Plus2.6 J (1.92 ft-lb)0 to 1,500 RPM6.05 lb listed3-year warranty
Buy it if
You run DEWALT 20V batteries and drill a lot of overhead anchors where a cord gets in the way.
Skip it if
You drill pipe core holes. DEWALT doesn't list a core capacity, and the Makita HR2641 does.
DEWALT's DCH133B is my top pick, and the reason is in DEWALT's own words. Its product page lists the jobs it's made for: forming, rod hanging, structural connections, beam and column anchorage, steel stanchion mounting, and clip and bracket mounting. Rod hanging and clip mounting are plumbing work.
On a pipe run, the anchors go in overhead, one at every hanger, often from a lift or a ladder. That's where a cordless hammer pays for itself. There's no cord to drag along the run, and nothing to snag on the rack you just hung.
DEWALT lists 2.6 joules of impact energy, which works out to about 1.92 ft-lb. That's a little under the Makita HR2641's 2.9 J and well above the 1.2 J of the Makita XRH06ZB. A brushless motor drives a mechanism DEWALT calls German-engineered.
DEWALT's spec table lists a 1,500 RPM top speed, an assembled weight of 6.05 lb and a length of 16.2 in. DEWALT doesn't say whether that weight includes a battery. With a 20V pack on the bottom, plan on holding more than that number over your head.
There's one gap in DEWALT's numbers. It calls the DCH133B a 1 in. rotary hammer and lists 2.6 J, but it doesn't publish a blow rate, a best hole range or a core capacity. That's why it shows "Not listed" in the anchor and core charts, even though DEWALT names it for rod hanging.
A rotating dial sets it to drill, hammer drill or chip mode. The listing says the box includes the hammer, a 360° side handle and a depth rod. Set the depth rod for every hole: drop-in anchors need the right depth to set flush, and Simpson adds 1/8 in. to the embedment for that.
Its product page lists DEWALT's 3-year limited warranty, plus 1 year of free service and a 90-day satisfaction guarantee. Amazon.com sold it new and in stock on the day of the update, as the bare tool with no battery.
Hammers sized for hanger anchor holes
Hanger rod anchors set the hole size. Find your rod size, then read across to see where each hammer's listed range puts that bit.
Rod size and anchor
Bit and depth
Makita HR2641
DEWALT DCH133B
Bosch GBH2-28L
DEWALT D25481K
Bosch 11255VSR
Makita XRH06ZB
Listed sweet spot
1/4 to 5/8 in.
Not listed
Not listed
Not listed
3/16 to 5/8 in.
5/32 to 3/8 in.
Listed max in concrete
1 in.
Not listed
1-1/8 in.
1-9/16 in. class
1 in.
11/16 in.
3/8 in. rod, Simpson DIA37S
1/2 in. bit, 7/8 in. deep
Sweet spot
Range not listed
Under max
Range not listed
Sweet spot
Above sweet spot
1/2 in. rod, Simpson DIA50S
5/8 in. bit, 1-1/8 in. deep
Sweet spot
Range not listed
Under max
Range not listed
Sweet spot
Above sweet spot
Bit sizes and embedments from Simpson Strong-Tie's DIAS short drop-in anchor table; depth is the embedment plus 1/8 in., per Simpson's install steps. Hammer ranges from Makita's, DEWALT's and Bosch's product pages, read Oct 19, 2026. "Sweet spot" means the bit falls in the maker's optimum range.
Two of these hammers list a range that covers both common drop-in bits: the Makita HR2641 and the Bosch 11255VSR. The Bosch GBH2-28L will drill both, since its 1-1/8 in. maximum is well above them, but Bosch doesn't publish a best range for it.
The surprise is the Makita XRH06ZB. Its 11/16 in. maximum covers a 1/2 in. or 5/8 in. bit, but its listed best range stops at 3/8 in. That makes it a good hammer for strap and clip anchors and a slower one for hanger rod. DEWALT names the cordless DCH133B for rod hanging, though it doesn't list a range.
Makita HR2641: anchor holes, plus cores to 3-1/8 in.
Prices and availability are accurate as of the time shown and may change.
Pros
Core bit capacity of 3-1/8 in., per Makita
Optimum range 1/4 to 5/8 in. covers common anchor bits
AVT counterbalance, 11.5 m/s² listed
Torque-limiting clutch, per the listing
Sold by Amazon.com
Cons
Corded, so you need power on site
7.1 lb to hold overhead
No electronic bind-up control in Makita's spec table
1 in. max in concrete3-1/8 in. core bit2.9 J (2.1 ft-lb)0 to 4,500 BPM13.1 ft. cord
Buy it if
You drill hanger anchors and pipe core holes on jobs with power, and want one hammer for both.
Skip it if
You drill mostly overhead with no outlet nearby. A cordless hammer saves running a cord up the ladder.
Makita's HR2641 is my pick when coring is part of the job, because it's the hammer here with the clearest numbers for both jobs a plumber drills: anchor holes and core holes. Makita lists a 1 in. maximum in concrete, an optimum range of 1/4 to 5/8 in., and a core bit capacity of 3-1/8 in.
The optimum range matters more than the maximum. It's the hole size the hammer drills best, and it covers the 1/2 in. and 5/8 in. bits that Simpson Strong-Tie calls for on its 3/8 in. and 1/2 in. drop-in anchors. Those are the anchors behind most hanger rod.
The 3-1/8 in. core figure is the other reason. A 2-1/2 in. steel pipe is 2.875 in. across under ASME B36.10, so a 3-1/8 in. core clears it. That's the biggest core capacity listed among these six, and it's why the HR2641 tops the core-hole chart below.
Makita lists 2.9 joules (2.1 ft-lb) of impact energy, 0 to 4,500 blows per minute and 0 to 1,100 RPM, all variable from the trigger. It's corded, with an 8 amp motor and a 13.1 ft. cord, so it doesn't slow down at the end of a battery.
Vibration is where the AVT name comes from. Makita describes an internal counterweight that moves opposite the drive piston, plus a damper spring that soaks up blows from the bit. Makita lists 11.5 m/s² of vibration, and the Makita XRH06ZB lists 9 m/s².
The listing names a torque-limiting clutch that disengages the gears if the bit binds. Makita's spec table lists bind-up control as "No", which I read as no electronic sensor like Bosch's KickBack Control. Keep a firm grip on the D-handle and side handle either way.
It has three modes (rotation only, hammering with rotation and chipping only), 40 bit angle settings for chisel work and a retractable hook for hanging it off a ladder or rail. The weight is 7.1 lb and the length is 16-5/8 in., per Makita.
It was sold new by Amazon.com and in stock on the day of the update, as the corded HR2641.
Which pipe each core bit size clears
Coring a hole for pipe through a wall or slab? Find your pipe size, then read across. Each hammer's listed core capacity is compared with the pipe's outside diameter.
Steel pipe size
Outside diameter
Makita HR2641
Bosch GBH2-28L
Bosch 11255VSR
DEWALT DCH133B
DEWALT D25481K
Makita XRH06ZB
Listed core capacity
3-1/8 in.
2-5/8 in.
2-5/8 in.
Not listed
Not listed
Not listed
1-1/4 in.
1.660 in.
Clears
Clears
Clears
1-1/2 in.
1.900 in.
Clears
Clears
Clears
2 in.
2.375 in.
Clears
Clears
Clears
2-1/2 in.
2.875 in.
Clears
Too small
Too small
3 in.
3.500 in.
Too small
Too small
Too small
Outside diameters from the ASME B36.10 steel pipe table published by Engineering ToolBox. Core capacities from Makita's and Bosch's product pages, read Oct 19, 2026. "Clears" means the listed core capacity is bigger than the pipe's outside diameter.
Bar length is the nominal pipe size, out of 2-1/2 in. The other three makers don't list a core capacity.
The chart is for the bare pipe. If the job calls for a sleeve through the wall or slab, size the hole to the sleeve's outside diameter instead, which pushes you one size down this chart. A 2-5/8 in. core leaves only about 1/4 in. around a 2 in. pipe.
That's my reason for picking the Makita HR2641 when coring is part of the job. Its 3-1/8 in. capacity gives a 2 in. pipe room for a sleeve or a fire-stop collar, and it takes 2-1/2 in. pipe bare. For 3 in. and 4 in. drains, rent or buy a core drill rig.
Bosch GBH2-28L: 1-1/8 in. holes with KickBack Control
Best for holes up to 1-1/8 in. with bind-up protection
Check the seller on Amazon before you buy · low stock · price as of Nov 2, 2026, 5:41 AM EST
Prices and availability are accurate as of the time shown and may change.
Pros
KickBack Control stops rotation on bind-up
1-1/8 in. max in concrete, per Bosch
2.4 ft-lb EPTA impact energy
Reverse, and works with Bosch dust hoods
Check the seller on Amazon before you buy
Cons
Bosch lists two different blow rates
No best hole range listed
Low stock on the day of the update
1-1/8 in. max in concrete2-5/8 in. core bit2.4 ft-lb EPTA0 to 1,230 RPM6.9 lb
Buy it if
You drill larger anchor holes and want a sensor that stops the bit spinning if it catches rebar.
Skip it if
You need to core for 2-1/2 in. pipe. Its 2-5/8 in. core capacity stops at 2 in. pipe.
Bosch's GBH2-28L is the corded pick for drillers who want bind-up protection. Bosch describes KickBack Control as an integrated sensor that stops tool rotation when the bit binds. That's the moment a rotary hammer can twist your wrist, often when a bit hits rebar in a slab.
None of the other picks lists an electronic sensor like it. The Makita HR2641's listing names a mechanical torque-limiting clutch, and DEWALT's D25481K shows an integral mechanical clutch. On overhead holes from a ladder, a tool that stops spinning on its own is the safer one to hold.
Bosch lists 1-1/8 in. as the maximum in concrete, the largest of the SDS-Plus hammers here, plus a 2-5/8 in. core bit capacity. In the core chart, that core size clears 2 in. steel pipe at 2.375 in. and stops short of 2-1/2 in. pipe at 2.875 in.
Impact energy is 2.4 ft-lb, measured to the EPTA method Bosch names. That converts to about 3.25 joules. Bosch's technical data lists 0 to 5,460 blows per minute, but its product highlights say 0 to 5,100. I've used the technical data figure in the charts and flagged the gap here.
An 8.5 amp motor runs it, with 0 to 1,230 RPM. The weight is 6.9 lb and the length is 17.4 in., per Bosch. Bosch lists counter-balanced Vibration Control, a variable-speed reversing trigger, a D-handle and Vario-Lock for setting a chisel angle.
It has three modes: drilling only, hammer drilling and chiseling. The HammerHook lets you hang it on a rail or ladder between holes. Bosch says it works with its GDE18V-26D on-tool dust extractor and HDC100 and HDC200 dust hoods, which matters on silica jobs.
The box includes an auxiliary handle, a depth gauge and a carrying case, per Bosch. It was sold new by Amazon.com and in stock on the day of the update, with low stock showing.
Impact energy: how hard each hammer hits
Impact energy is the force of each blow. More energy drills bigger holes faster, at the cost of weight.
* Converted from Bosch's ft-lb figures at 1 ft-lb = 1.356 J. Bosch names the EPTA test method; the others don't say how they measured.
Hammer
Impact energy listed
Blows per minute
RPM
Power
DEWALT D25481K
6.1 J
3,150
540
Corded, SDS Max
Bosch GBH2-28L
2.4 ft-lb EPTA
0 to 5,460 (or 5,100)
0 to 1,230
8.5 amp corded
Makita HR2641
2.9 J (2.1 ft-lb)
0 to 4,500
0 to 1,100
8 amp corded
Bosch 11255VSR
2.0 ft-lb EPTA
0 to 5,800
0 to 1,300
8.0 amp corded
DEWALT DCH133B
2.6 J
Not listed
1,500
20V MAX
Makita XRH06ZB
1.2 J (0.88 ft-lb)
0 to 4,800
0 to 680
18V LXT
From Makita's, DEWALT's and Bosch's product pages, read Oct 19, 2026. DEWALT's D25481K blow rate and speed come from the labeled feature image on its product page. Bosch lists 5,460 BPM in the GBH2-28L's technical data and 5,100 in its highlights.
Read impact energy as a rough guide, not a contest. Makers don't all say how they measured it, and a few tenths of a joule won't change how a 1/2 in. anchor hole drills. The big gaps are real, though: the SDS Max DEWALT hits about twice as hard as the SDS-Plus hammers, and the sub-compact Makita hits less than half as hard.
My rule: for hanger anchors, about 2 to 3 joules is plenty. The jump to 6 joules earns its weight only on big holes and on chipping out slab.
Prices and availability are accurate as of the time shown and may change.
Pros
6.1 J of impact energy, per DEWALT
SHOCKS Active Vibration Control
Integral mechanical clutch
Hard kit case included
Sold by Amazon.com
Cons
20.75 lb listed: not an overhead tool
Takes SDS Max bits, not SDS-Plus
No core capacity listed
1-9/16 in. (40 mm) classSDS Max6.1 J3,150 BPM, 540 RPM9.8 ft. cord
Buy it if
You break out slab for drains and trenches, or drill holes too big for an SDS-Plus hammer.
Skip it if
Your holes are hanger anchors. At 20.75 lb listed, it's too heavy to hold overhead all day.
DEWALT's D25481K is the heavy hammer on this list, and it's for a different job than the other five. DEWALT calls it a 1-9/16 in. (40 mm) SDS Max combination hammer. Combination means it drills with hammering and also chips, so it can break out concrete as well as drill it.
On plumbing work, that's the hammer for slab. Breaking out concrete for a new floor drain, a shower drain or a trench for a sewer line goes faster with a bigger blow. DEWALT lists 6.1 joules in its features, about twice what the SDS-Plus hammers here list.
DEWALT's overview rounds that to 6 joules, and its features say 6.1, so I've used 6.1 in the chart. The labeled feature image on DEWALT's page lists 3,150 blows per minute, 540 RPM no-load speed, a 3-mode dial, an integral mechanical clutch and a 9.8 ft. cord.
The weight is the trade-off. DEWALT's spec table lists an assembled weight of 20.75 lb and a length of 22.8 in. That's about three times the SDS-Plus hammers. It's a tool you hold at waist height or point down at a floor, never one you hold over your head.
DEWALT's SHOCKS Active Vibration Control is the feature that makes a hammer this size bearable. DEWALT says it reduces the vibration you feel at the handles. DEWALT also lists horizontal serial drilling, and the listing names rebar doweling for #4 to #8 rebar.
One thing to plan for: it takes SDS Max bits and chisels, which are a different shank from the SDS-Plus bits the other five use. If you already own SDS-Plus bits, they won't fit this hammer. The SDS-Plus and SDS Max section below covers when that switch is worth it.
It comes in a hard kit case. DEWALT’s page lists a 3-year limited warranty, a year of free service and a 90-day satisfaction guarantee for it. It was sold new by Amazon.com and in stock on the day of the update.
SDS-Plus or SDS Max: which shank you need
The shank is how the bit locks into the hammer. It also sets the size class of the hammer and the bits you'll be buying.
SDS-Plus (5 picks here)
SDS Max (DEWALT D25481K)
Largest hole listed
Up to 1-1/8 in. (Bosch GBH2-28L)
1-9/16 in. (40 mm) class
Core bit listed
Up to 3-1/8 in. (Makita HR2641)
Not listed
Impact energy listed
1.2 to 2.9 J (about 3.25 J converted for the GBH2-28L)
6.1 J
Weight listed
4.6 to 7.1 lb
20.75 lb
Plumbing jobs
Hanger anchors, strap anchors, pipe cores
Breaking out slab, big holes
Overhead work
Yes
No, too heavy
From Makita's, DEWALT's and Bosch's product pages, read Oct 19, 2026. The plumbing-jobs rows are my call.
For most plumbers, SDS-Plus is the answer. Hanger anchors, strap anchors and pipe cores up to 2-1/2 in. are all inside what the SDS-Plus hammers here list, and those hammers weigh a third of the SDS Max one. Your SDS-Plus bits fit all five.
SDS Max earns a place when you break out a lot of slab or drill holes over about 1-1/8 in. in solid concrete. If that's once a year, renting one is a fair choice. If it's every week, the D25481K is the pick.
Prices and availability are accurate as of the time shown and may change.
Pros
0 to 5,800 BPM, the highest listed here
Sweet spot 3/16 to 5/8 in. covers anchor bits
Hole sizes listed for steel and wood
Comes with 7 SDS-plus bits, 3/16 to 1/2 in.
Sold by Amazon.com
Cons
2.0 ft-lb EPTA, the lowest of the corded picks
No KickBack Control sensor, unlike the GBH2-28L
Bare tool not in stock on Amazon on the day of the update
1 in. max in concrete2-5/8 in. core bit2.0 ft-lb EPTA0 to 5,800 BPM6.7 lb
Buy it if
You drill anchor holes in concrete and also drill steel strut and wood blocking with the same tool.
Skip it if
You need more hitting power for big holes. The Bosch GBH2-28L lists 2.4 ft-lb and 1-1/8 in.
Bosch's 11255VSR is the corded hammer with the most complete hole-size list here. Bosch lists a 1 in. maximum in concrete, a 2-5/8 in. core bit, 1/2 in. in steel and 1-1/4 in. in wood, plus an optimal concrete range of 3/16 to 5/8 in. No other pick lists steel and wood sizes.
That matters on plumbing jobs where the holes aren't all in concrete. Drilling a strut channel or a steel beam clip, or boring wood blocking for a pipe, is rotation-only work. Bosch lists a rotation-only mode and a keyless 3-jaw chuck with SDS-plus shank, the HA3JAW, that works with it.
Its optimal range of 3/16 to 5/8 in. covers both Simpson drop-in bits in the anchor chart, the same as the Makita HR2641. The 2-5/8 in. core capacity matches the GBH2-28L, so it clears 2 in. steel pipe bare.
Bosch lists 0 to 5,800 blows per minute, the highest listed of these six, and 0 to 1,300 RPM. Impact energy is 2.0 ft-lb, measured to EPTA, or about 2.71 joules. That's less per blow than the GBH2-28L's 2.4 ft-lb, with more blows per minute.
Bosch’s technical data and product highlights list an 8.0 amp motor. The weight is 6.7 lb and the length is 17.25 in., per Bosch.
Bosch calls this its PRO+GUARD dust system and says it helps users move toward OSHA Silica Table 1 compliance. Bosch lists the GDE18V-26D extractor and HDC100 and HDC200 hoods as working with it; they're sold separately. The dust section below shows what Table 1 asks for.
It has three modes (rotary hammer, rotation only and hammer only), Vario-Lock with 36 chisel positions, a variable-speed reversing trigger and a HammerHook. Bosch says the tool comes with an auxiliary handle, a depth gauge and a carrying case.
On Oct 21 the bare tool wasn’t in stock, so this links Amazon.com’s kit with Bosch’s HCK001 bits. Bosch lists seven carbide-tipped SDS-plus bits from 3/16 to 1/2 in., 4 or 6 in. long. That includes the 1/2 in. bit a 3/8 in. drop-in anchor takes. A 1/2 in. drop-in still needs a 5/8 in. bit, bought separately.
Weight, vibration and bind-up protection
You hold a rotary hammer against the work for every hole. Weight, vibration and what happens when a bit binds decide how the day goes.
Hammer
Weight listed
What it includes
Vibration control
Bind-up protection
Makita XRH06ZB
4.6 lb
With battery, per Makita
Handle moves separately; 9 m/s²
None listed
DEWALT DCH133B
6.05 lb
Not stated
Not listed
Not listed
Bosch 11255VSR
6.7 lb
Corded
Vibration control, per the listing
Not listed
Bosch GBH2-28L
6.9 lb
Corded
Counter-balanced
KickBack Control sensor
Makita HR2641
7.1 lb
Corded
AVT counterbalance; 11.5 m/s²
Torque-limiting clutch
DEWALT D25481K
20.75 lb
Corded
SHOCKS active control
Integral mechanical clutch
From Makita's, DEWALT's and Bosch's product pages and the makers' text on the Amazon listings, read Oct 19, 2026. DEWALT's weights are the "assembled product" weight in its spec table. Only Makita publishes a vibration number.
Only Makita says the XRH06ZB's weight includes a battery. DEWALT doesn't say for the DCH133B.
The five SDS-Plus hammers sit within about 2-1/2 lb of each other. The real difference overhead is balance and vibration, and only Makita publishes vibration numbers: 11.5 m/s² for the HR2641 and 9 m/s² for the XRH06ZB.
Bind-up is the safety point. When a bit catches rebar, the hammer body wants to spin instead of the bit. Bosch's KickBack Control stops rotation with a sensor. A mechanical clutch slips instead. Either way, use the side handle on every hole, and keep your footing solid on a ladder.
Makita XRH06ZB: 4.6 lb with battery and 10-3/4 in. long
Prices and availability are accurate as of the time shown and may change.
Pros
4.6 lb with battery, per Makita
10-3/4 in. long, the shortest here
Brushless motor
Vibration-absorbing handle, 9 m/s² listed
Sold by Amazon.com
Cons
Sweet spot stops at 3/8 in.
1.2 J, the lowest impact energy here
Battery and charger sold separately
11/16 in. max in concrete5/32 to 3/8 in. sweet spot1.2 J (0.88 ft-lb)0 to 4,800 BPM18V LXT
Buy it if
You drill small holes for pipe straps, clips and small concrete screws between joists and in tight chases.
Skip it if
You drill 1/2 in. holes for 3/8 in. rod anchors all day. It'll drill them, but that's above its listed best range.
Makita's XRH06ZB is the small hammer on this list. Makita lists 4.6 lb with a battery and a length of 10-3/4 in., the lightest and shortest pick here. It's the one that fits between joists, inside a chase or under a sink cabinet where a 16 in. hammer won't.
Makita is clear about what it's best at. The spec table lists an 11/16 in. maximum in concrete and an optimum range of 5/32 to 3/8 in. That range covers the small holes for pipe straps, clips and small concrete screws, which is a lot of a plumber's anchoring.
It's less suited to hanger rod. A 3/8 in. drop-in anchor takes a 1/2 in. bit, per Simpson, and a 1/2 in. drop-in takes 5/8 in. Both are under the XRH06ZB's maximum but above its best range. For a run of rod hangers, the DEWALT DCH133B or the Makita HR2641 is the better pick.
Makita lists 1.2 joules (0.88 ft-lb) of impact energy, 0 to 4,800 blows per minute and 0 to 680 RPM, from a brushless motor. The low energy fits its size: small holes in concrete don't need a heavy blow, and a light blow is easier to control in a tight spot.
The handle moves separately from the motor and hammer mechanism, per the listing, and Makita lists vibration at 9 m/s², lower than the HR2641's 11.5 m/s². It runs on Makita 18V LXT batteries and uses SDS-Plus bits like the other SDS-Plus picks.
Makita's spec table lists bind-up control as "No", and Makita doesn't list a core capacity. That's fine for its job. It's a second hammer for small anchors, not a replacement for a 1 in. hammer.
It was sold new by Amazon.com and in stock on the day of the update, as the tool-only XRH06ZB, with no battery or charger in the box.
Concrete dust and OSHA's silica rule
Drilling concrete makes silica dust. OSHA's construction silica standard lists what a rotary hammer needs to follow its Table 1 method.
What OSHA Table 1 lists for handheld rotary hammer drills
What it means on the job
A shroud or cowling with a dust collection system
A dust hood on the bit, connected to a vacuum or extractor
Operate and maintain the tool per the maker's instructions
Follow the hammer and hood manuals
Dust collector with the maker's recommended air flow or more
Match the vacuum to what the hood maker lists
A filter with 99% or greater efficiency and a filter-cleaning mechanism
Not every shop vac qualifies; check the filter
A HEPA-filtered vacuum when cleaning holes
Vacuum the hole out with a HEPA vac
Respirator required
None listed for this task when the method is followed
From OSHA 29 CFR 1926.1153, Table 1, the row for handheld and stand-mounted drills including impact and rotary hammer drills, read Oct 19, 2026. The right-hand column is my plain reading.
Hammer
Dust gear the maker lists
Bosch 11255VSR
PRO+GUARD; works with GDE18V-26D, HDC100, HDC200
Bosch GBH2-28L
Works with GDE18V-26D, HDC100, HDC200
Makita HR2641
Not on the pages I read
DEWALT DCH133B
Not on the pages I read
DEWALT D25481K
Not on the pages I read
Makita XRH06ZB
Not on the pages I read
Bosch is the only maker here whose product pages name the dust gear that fits. That doesn't mean the others can't take a hood; it means you'll have to find one that fits and check its air flow yourself. Simpson also notes that overhead anchor holes need not be blown clean, which helps on hanger work.
For cleanup, OSHA's Table 1 calls for a HEPA-filtered vacuum. Our shop vac picks list which filters each one takes.
The six picks side by side
Hammer
Best for
Max in concrete
Core bit
Impact energy
Weight listed
Power
Makita HR2641
Anchors and cores
1 in.
3-1/8 in.
2.9 J
7.1 lb
Corded
DEWALT DCH133B
Overhead rod anchors
Not listed
Not listed
2.6 J
6.05 lb
20V MAX
Bosch GBH2-28L
Holes to 1-1/8 in.
1-1/8 in.
2-5/8 in.
2.4 ft-lb
6.9 lb
Corded
DEWALT D25481K
Slab and big holes
1-9/16 in. class
Not listed
6.1 J
20.75 lb
Corded, SDS Max
Bosch 11255VSR
Concrete, steel, wood
1 in.
2-5/8 in.
2.0 ft-lb
6.7 lb
Corded
Makita XRH06ZB
Small anchors
11/16 in.
Not listed
1.2 J
4.6 lb
18V LXT
From each maker's product page, read Oct 19, 2026. All six were sold new by Amazon.com and in stock on Oct 21, the Bosch 11255VSR as a kit with bits.
How to drill and set a drop-in anchor for hanger rod
1
Pick the bit from the anchor
Use the size the anchor maker lists: 1/2 in. for Simpson's 3/8 in. drop-in, 5/8 in. for its 1/2 in. drop-in.
2
Set the depth
Set the depth rod to the embedment plus 1/8 in., per Simpson's install steps.
3
Drill in hammer mode
Use rotary hammer mode and the side handle. Let the hammer do the work.
4
Clear the hole
Simpson says to blow holes clean, and that overhead holes need not be. OSHA Table 1 calls for a HEPA vacuum.
5
Tap the anchor flush
Insert the anchor and tap it until it's flush with the surface.
6
Set it with the setting tool
Drive the plug with the matching setting tool until its shoulder meets the anchor.
From Simpson Strong-Tie's DIAS drop-in anchor install steps, read Oct 19, 2026. Follow the anchor maker's steps and load tables for your anchor, and the hammer maker's manual.
The setting tool is the step people skip. A drop-in anchor holds only when its plug is driven all the way, and the matching setting tool is sized so its shoulder stops at the right point. Simpson's short drop-ins come with one. Our concrete anchor picks and clevis vs. split-ring hanger guide cover what hangs from the rod.
How to choose a rotary hammer for plumbing
If you mostly…
Look for
My pick
Drill anchors and core pipe holes
A listed core capacity over your pipe's OD
Makita HR2641
Drill rod anchors overhead, cordless
A 1 in. class cordless hammer
DEWALT DCH133B
Drill bigger holes and hit rebar
Bind-up protection and 1-1/8 in.
Bosch GBH2-28L
Break out slab for drains
SDS Max and high impact energy
DEWALT D25481K
Drill concrete, steel and wood
Listed sizes for all three
Bosch 11255VSR
Drill small strap anchors in tight spots
Short and light, with a small sweet spot
Makita XRH06ZB
Start with the hole you drill most. For hanger rod, that's a 1/2 in. or 5/8 in. bit, so pick a hammer whose listed range covers it. Then decide on a cord: corded for coring and long days, cordless for overhead runs. Last, check the core capacity against your biggest pipe.
If I could have only one, it's the DEWALT DCH133B. DEWALT names rod hanging among its jobs, and with no cord it goes up the lift with you. If you core pipe holes often, add the Makita HR2641, which lists a 3-1/8 in. core capacity. For bits, see our masonry drill bit picks.
Questions people ask
What is the best rotary hammer for plumbers?
My pick is the DEWALT DCH133B. DEWALT names rod hanging among its jobs, and it's cordless for overhead runs. For coring, the Makita HR2641 lists a 3-1/8 in. core capacity.
Is a rotary hammer worth it?
My call: if you drill concrete for hanger anchors or pipe holes every week, yes. If it's a few holes a year, renting one is a fair choice.
Which is better, SDS-Plus or SDS Max?
For anchors and pipe cores, SDS-Plus. SDS Max hammers hit harder but weigh far more; DEWALT lists 20.75 lb for its D25481K.
What size bit do I need for a 3/8 in. drop-in anchor?
Simpson Strong-Tie lists a 1/2 in. bit for its 3/8 in. short drop-in, and a 5/8 in. bit for its 1/2 in. drop-in.
Can a rotary hammer drill core holes for pipe?
Yes, with a core bit. Makita lists up to 3-1/8 in. for the HR2641, and Bosch lists 2-5/8 in. for the GBH2-28L and 11255VSR.
What size core hole do I need for 2 in. pipe?
2 in. steel pipe is 2.375 in. across, so a 2-5/8 in. core clears it bare. Size up if you're setting a sleeve.
Is a cordless rotary hammer good enough for anchors?
For anchors, yes. DEWALT names rod hanging among the jobs for its cordless DCH133B, and it lists 2.6 J of impact energy.
What is the lightest rotary hammer here?
The Makita XRH06ZB, at 4.6 lb with a battery, per Makita. Its best range is 5/32 to 3/8 in., so it suits small anchors.
What does KickBack Control do?
Bosch says it's an integrated sensor that stops tool rotation when the bit binds. It's on the Bosch GBH2-28L.
Do I need dust collection when drilling concrete?
OSHA's Table 1 method for rotary hammers calls for a shroud with a dust collector and a HEPA vacuum for cleaning holes.
Can a rotary hammer drill steel and wood?
In rotation-only mode with a chuck adapter, yes. Bosch lists 1/2 in. in steel and 1-1/4 in. in wood for the 11255VSR.
Why isn't Milwaukee on this list?
On the day of the update, Amazon's Milwaukee rotary hammer listings came from third-party sellers with no price showing, so I picked hammers I could show a price for.
How I picked these
Why trust me
I'm Isaac Daniels, a licensed journeyman plumber in Georgia (license #JP507711). I picked these for the holes a plumber drills: hanger anchors overhead, strap anchors, pipe cores and slab for drains.
How I pick
One hammer per kind of job, so each pick does something the others don't.
Facts from maker product pages, read the same day, plus Simpson Strong-Tie's anchor table, a published ASME B36.10 pipe table and OSHA's silica standard. Anything a maker doesn't list is marked "Not listed".
Genuine branded hammers, new and in stock, sold by Amazon.com, except the Bosch GBH2-28L. Check the seller on Amazon before you buy.
Prices read from Amazon with the time shown, never typed in. No scores, because makers measure impact energy and weight in different ways.
Sources
Makita HR2641 and XRH06ZB: makitatools.com product pages and specifications, plus Makita's text on the Amazon listings, read Oct 19, 2026.
DEWALT DCH133B: dewalt.com product page, overview, features and specifications, plus the Amazon listing's box contents, read Oct 19, 2026.
DEWALT D25481K: dewalt.com product page, overview, features, labeled feature image and specifications, plus the Amazon listing, read Oct 19, 2026.
Bosch GBH2-28L and 11255VSR: boschtools.com product pages, technical data and product highlights, plus Bosch's text on the Amazon listings, read Oct 19, 2026.
Bosch HCK001 bit set (sizes, lengths, pack of 7): boschtools.com SDS-plus Bulldog rotary hammer drill bit sets page, read Oct 21, 2026. Kit contents from the Amazon listing, read Oct 21, 2026.
Drop-in anchor bit sizes, embedment and install steps: Simpson Strong-Tie, Drop-In (DIAS) short internally threaded anchor page, read Oct 19, 2026.
Silica dust: OSHA 29 CFR 1926.1153, Table 1, handheld and stand-mounted drills, read Oct 19, 2026.
CPSC recalls: saferproducts.gov searched for rotary hammers and these model numbers on Oct 19, 2026. No recalls for these models; the one rotary hammer match is a 2000 recall of older tools.
Amazon product data (prices, sellers, stock, photos), refreshed daily; each price shows the time it was read.