You’ve found the faucet you want. Then you look under the sink and count holes : and the number doesn’t match. I check the hole layout before buying so the faucet and mounting hardware fit.

Faucet rocking on the deck? That is a separate fix : tightening a loose faucet base.

As an Amazon Associate I earn from qualifying purchases.

Count your holes first

There is no one opening diameter that fits every kitchen faucet. For example, the Moen Adler 87233 specification calls for 1 or 3 holes, each at least 1½ inches (38 mm) in diameter, and a maximum deck thickness of 2½ inches. I use the drawing for the exact model before cutting. A cover’s outside diameter is not its required hole diameter. [Moen]

I inspect the actual mounting surface: the faucet may mount through the sink deck or through the countertop. I use the sink and faucet drawings to locate the required openings rather than assuming from the sink type. A wall-mounted faucet is a different installation; I confirm its supply and wall requirements before choosing it. [Moen]

  • 1 hole : a compatible single-hole faucet; I confirm the selected model’s required openings. [Moen]
  • 2 holes : faucet plus one accessory (sprayer, soap dispenser, or air gap). [GE]
  • 3 holes : either a widespread faucet (handles separate from spout) or a single-handle faucet plus two accessories. [Moen]
  • 4 holes : a three-hole faucet plus an accessory, or a single-hole faucet plus three accessories. Count occupied openings rather than assuming what each hole is for. [Moen]

I measure center to center between the outer mounting holes. Moen’s Bexley 87403 drawing shows an 8-inch spread; its Eva 6410 bathroom faucet shows a 4-inch centerset layout. Those are examples, not a substitute for measuring the sink and checking the exact drawing. A plate must cover the openings and fit the faucet shank. [Moen] [Moen]

The measurement nobody tells you to take: deck thickness

I check deck thickness along with hole count and spacing before buying. The faucet drawing states the permitted mounting range; I measure the whole stack while it is accessible. [Moen]

I compare the complete mounting stack with the faucet drawing. Countertop, substrate, plate and gasket all count toward the material the mounting hardware must clamp through. I choose hardware whose published range accommodates that stack, rather than assuming that a threaded shank will fit. [Moen]

So before you buy:

  • Identify the mounting surface. I check the sink and countertop drawings to see where the faucet actually mounts. [Moen]
  • Measure the full stack, including anything you are adding under the base. [Moen]
  • Check the faucet’s stated maximum deck thickness before ordering, and if you are close, choose a model whose specified range covers the whole stack : the published mounting range decides whether it fits. [Moen]

The rule that avoids unnecessary drilling

Unused accessory holes can often be covered. You cannot easily add one.

I prefer a compatible faucet or cover before planning a new opening. If another opening is necessary, I have the installer identify the sink or countertop material and follow its manufacturer’s cutting instructions. I do not apply one drilling method to stainless steel, stone, composite and coated cast iron. A spare opening may also suit an accessory if its required dimensions and connections fit.

Too many holes: a deck plate or a hole cover

A deck plate (escutcheon) is a single plate that sits under the faucet base and spans the extra holes : the standard answer when you’re putting a single-hole faucet into a 3-hole sink. Many faucets ship with one; check the box before buying another. [Moen]

    MAYYAYA 10" Kitchen Sink Deck Plate, Faucet Hole Cover, 8" Widespread
  • MAYYAYA 10″ deck plate for 8″ widespread, brushed nickel stainless

    The listing specifies coverage for the named widespread layout, fastening with the faucet’s own hardware and a foam gasket. I check actual coverage and shank fit before ordering.

    $7.69 at AmazonPrice as of Nov 22, 2026, 9:30 AM ESTCheck price on Amazon

    Buy it if the compatible faucet and plate cover your unused outer holes. Skip it if an accessory hole sits beyond the plate or the shank opening does not fit. The tradeoff: the plate changes the visible base and adds to the mounting stack.

  • Product photo from the Amazon listing.

If the hole you need to hide is away from the faucet : an old sprayer or soap dispenser opening off to one side : a deck plate won’t reach it. Use a snap-in cover instead:

    Plumb Pak PP21522 Snap-in Faucet Hole Cover, 1-1/2 in Od, Stainless Steel
  • Plumb Pak PP21522 snap-in faucet hole cover, 1-1/2″ OD stainless

    The snap-in design uses retaining tabs. I check the opening and tab fit before ordering.

    $5.53 at AmazonPrice as of Nov 22, 2026, 9:30 AM ESTCheck price on Amazon

    Buy it if the cover dimensions and retaining tabs fit an unused accessory opening. Skip it if the hole serves a required air gap or the cover cannot grip the deck. The tradeoff: a separate cap remains visible and does not support a faucet.

  • Product photo from the Amazon listing.

Match the finish to the faucet, not the sink. A chrome plate under a brushed-nickel faucet reads as a mistake from across the room.

Do you actually need the air gap hole?

A spare deck hole may hold a dishwasher air gap, and whether you need one is a live code question rather than a style choice : which is why it is worth checking before you cover it over permanently. [GE]

I check the currently adopted local plumbing code and the dishwasher installation instructions before changing an air gap. A high loop raises and secures the waste hose under the sink rim or countertop; it is not the same device as a deck-mounted air gap. Keep an existing air gap until the local authority and appliance instructions confirm the permitted waste connection. Water-supply backflow protection is a separate requirement. [GE]

I leave a working dishwasher air gap in place until the appliance instructions and local requirements confirm the permitted connection. GE distinguishes an air gap from a high drain loop; its instructions call for a high loop where an air gap is not required. I follow the instructions for the actual dishwasher, not a universal height or a faucet accessory listing. [GE]

Not enough holes

Fewer options, so I check compatibility before deciding to drill:

  • Pick a compatible faucet. A single-hole pull-down model such as the Adler can provide its spray function without a separate side-sprayer opening. Other required accessories still need their own space. [Moen]
  • Check the stainless sink maker’s cutting instructions. I have the installer confirm the permitted method and finish the edge as directed before seating a gasket.
  • Use a qualified installer for stone, composite or coated cast iron. I require a material-specific plan before any cutting.

The order that makes install day short

I plan the sequence before disconnecting the old faucet. I read the exact installation instructions, lay out the specified hardware and make sure I can reach the mounting nut and supply connections. [Moen]

  1. Dry-fit the compatible plate and faucet. I check coverage, seating and finish before removing the old fixture.
  2. Lay out the mounting parts. I follow the maker’s assembly order rather than connecting every hose on the bench. [Moen]
  3. Isolate the water. I shut off the supplies, then open the faucet to relieve pressure and confirm shutoff before disconnecting it. [Moen]
  4. Prepare the mounting surface. I clean and dry it using methods safe for the sink or countertop finish. [Moen]
  5. Secure the faucet. I use the specified washer, bracket and mounting nut, align the faucet, and tighten with the maker’s tool and instructions. [Moen]
  6. Connect and flush as directed. I follow the model’s hose connection and flushing sequence, then check the connections for leaks. [Moen]

While you’re under there

I inspect the accessible supply connections and shutoffs before removal. If the shutoffs will not isolate the water or a connection leaks, I arrange repair before continuing. I keep the basin wrench or the maker’s mounting tool ready for the nut beneath the sink. I do not replace sound supply parts solely because the faucet is changing. [Moen]

I check the exact faucet’s rated flow and the local requirements rather than judging compatibility from a generic flow figure. For example, Moen lists the Adler 87233 at 1.5 gpm at 60 psi in its specification. Supply tubing connection size and the building supply-pipe sizing are different measurements. If flow is weak, I inspect the aerator before blaming the house supply. [Moen]

If the faucet itself is fine and only the sprayer is failing, that’s a smaller fix : see kitchen faucet sprayers. Shopping the faucet itself: best kitchen faucets.

FAQ

Can I use a 1-hole faucet in a 3-hole sink?

Yes, when the plate and faucet are compatible. Moen’s installation guide shows a deck plate for a three-hole mounting arrangement. I check the selected faucet’s instructions and included parts before ordering a separate plate.

What is standard kitchen faucet hole spacing?

I measure center to center between the outer mounting holes. Moen’s Bexley 87403 drawing shows an 8-inch spread; its Eva 6410 bathroom faucet shows a 4-inch centerset layout. Those are examples, not a substitute for measuring the sink and checking the exact drawing. A plate must cover the openings and fit the faucet shank. [Moen] [Moen]

Can I drill an extra hole in my sink?

I ask the installer to check the material and the sink or countertop maker’s instructions before adding a hole. I leave stone, composite and coated cast iron to a qualified installer. I do not prescribe one drill bit or cooling method for all materials.

Can I cover the dishwasher air gap hole?

I keep the existing air gap until the local authority and dishwasher instructions confirm whether it can be replaced by another permitted connection. A high loop is not a deck-mounted air gap. [GE]

Why won’t the mounting nut tighten on my new faucet?

I check deck thickness and the supplied mounting hardware first. The whole stack must fit within the faucet’s stated mounting range. If it does not, I stop and choose approved compatible hardware rather than forcing the nut. [Moen]

Do the holes go through the sink or the countertop?

I check the actual installation drawing. The mounting openings may be in the sink deck or countertop. That location determines what I measure and which surface would need modification. [Moen]

Sources

  • 1
    Moen Adler 87233 specification: hole diameter, count, maximum mounting thickness, escutcheon dimensions and rated flow. [Moen]
  • 2
    The two linked Amazon listings identify the MAYYAYA deck plate and Plumb Pak PP21522 cover. I verify accessory dimensions against the actual opening before ordering.

Related guides

Measure before choosing hardware

Measurement schematic: pin 1 marks opening diameter, pin 2 marks center spacing, pin 3 marks mounting stack thickness.
Measurement schematic, not a product drawing. Pins match the checks below.
  1. 1
    Measure the clear diameter across the opening. [Moen]
  2. 2
    Measure between hole centers, then compare the plate footprint. [Moen]
  3. 3
    Measure the whole mounting stack, including any substrate, plate and gasket. [Moen]

Hole size spec sheet

These dimensions describe the Moen Adler 87233 example, not every faucet. Source: Moen specification. [Moen] The accessories above are separate fit examples; I do not assume either fits the Adler without checking the shank and plate dimensions.

MeasurementAdler 87233 requirementWhat I check
Hole diameter 1½ in. minimum (38 mm) [Moen]Measure the opening, not the cover
Hole count 1 or 3 [Moen]Use compatible escutcheon hardware
Deck thickness 2½ in. maximum [Moen]Include substrate, plate and gasket
Escutcheon 10¼ × 2 3/8 in. [Moen]Check coverage in both directions

Moen specifies a maximum deck thickness of 2½ inches for the Adler 87233. [1] [Moen drawing]

Check the next step

Measure the opening diameter and full mounting stack first.

This check does not replace the exact faucet drawing or an in-person assessment. [Moen]

How I checked the fit advice

I kept the existing guide’s hole-count, coverage and installation outline. I checked both original accessories against their current Amazon listings and used Moen’s Adler 87233 drawing for an exact-model dimension example. Neither accessory replaces the faucet maker’s mounting instructions. CPSC recall search checked November 15, 2026: no matching recall for either listed accessory.