Best Pipe Locator: 5 Kits for Sondes and Metal Pipe

Three locator kits, matched to the pipe you’re chasing and the signal it can carry.

As an Amazon Associate I earn from qualifying purchases. How this site earns

RIDGID SR-20 locator and ST-305 transmitter
Product photo: Amazon

The short answer

My call: the RIDGID SR-20 with the ST-305 transmitter. It finds RIDGID’s 512 Hz drain sondes and traces metal pipe the ST-305 lights up. For long metal runs and tracer wire, the TEMPO 551. Own a RIDGID receiver? Add the ST-305 and sonde kit.

Best for sondes and metal line tracing in one kit
RIDGID SR-20 + ST-305
Best for sonde locates behind a sewer camera
RIDGID NaviTrack Scout + ST-305
Best for long metal runs and tracer wire to 20 ft deep
TEMPO 551 underground locator kit

The three locator kits

All genuine brand kits, new and in stock on Oct 22, 2026, 8:15 AM EDT. Prices are read from Amazon and show the time they were read.

  1. RIDGID SR-20 locator and ST-305 transmitter

    Product photo: Amazon

    Best for sondes and metal line tracing in one kit

    RIDGID SR-20 + ST-305

    RIDGID SeekTech SR-20 locator (21893) with ST-305 line transmitter (21898)

    Best for
    You chase both sondes in drains and metal water or gas lines, and you want one receiver that reads both.
    Skip it if
    Most of your work is long tracer wire or cable runs. The TEMPO 551 lists over a mile.
    $3,979.29 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
    Check it on Amazon (opens in a new tab)
  2. RIDGID NaviTrack Scout locator and ST-305 transmitter

    Product photo: Amazon

    Best for sonde locates behind a sewer camera

    RIDGID NaviTrack Scout + ST-305

    RIDGID NaviTrack Scout locator (19238) with ST-305 line transmitter

    Best for
    Most of your locates are a sonde in a drain or sewer, and you want the most direct screen for finding it.
    Skip it if
    You trace a lot of long metal lines at low frequency. The SR-20 hears 1 kHz and the Scout doesn’t.
    $2,652.16 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
    Check it on Amazon (opens in a new tab)
  3. TEMPO 551 receiver and transmitter in the hard case

    Product photo: Amazon

    Best for long metal runs and tracer wire to 20 ft deep

    TEMPO 551 underground locator kit

    TEMPO 551 underground locator kit

    Best for
    You trace long metal water lines, tracer wire on plastic gas or water service, or irrigation wire, often near power.
    Skip it if
    Your locates are mostly sondes in drains. The 551 lists 33 kHz sondes, and RIDGID’s camera sondes run at 512 Hz.
    $1,297.00 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
    Check it on Amazon (opens in a new tab)

The kits in detail

RIDGID SR-20 + ST-305: both jobs in one kit

Best for sondes and metal line tracing in one kit

RIDGID SeekTech SR-20 locator (21893) with ST-305 line transmitter (21898)

This Amazon bundle pairs RIDGID’s SR-20 receiver (21893) with the ST-305 line transmitter (21898), both new from Amazon.com. RIDGID sells its own kit, 46918, that adds a 4 in. inductive clamp. This bundle doesn’t have the clamp, so plan on direct connection.

The SR-20 is the most flexible receiver here. RIDGID lists sonde frequencies of 16, 512, 640 and 850 Hz and 8, 16 and 33 kHz, so it reads RIDGID’s 512 Hz 16728 sonde. RIDGID’s manual notes most SeeSnake reels carry a sonde in or behind the camera head.

For line tracing it lists 128 Hz, 1, 8 and 33 kHz, and it can be set to trace any frequency from 10 Hz to 35 kHz.

Passive mode listens for 50 and 60 Hz power, broadband under 4 kHz, and two radio bands. RIDGID’s OmniSeek scans all three bands at once, which helps when you’re sweeping a yard before you dig.

The ST-305 puts the signal on the pipe. It runs from 25 mA up to 5 W, at 1, 8, 33 or 262 kHz. In direct connect it can send two at once: 33 and 1 kHz, or 33 and 8 kHz. The SR-20 hears 1, 8 and 33 kHz, which covers every pair.

Depth shows continuously. RIDGID’s manual gives a quick test: note the depth, raise the receiver about 6 in., and the reading should rise about 6 in. If it doesn’t, the field is distorted, so treat the number with doubt.

Power is C cells. The SR-20 takes four (10 to 15 hours on alkaline, per RIDGID) or a RIDGID 18V pack with the SeekTech adaptor, for 18 to 22 hours. The ST-305 takes six C cells and shuts off after 1 to 4 hours, depending on power level.

Weight is the one muddle. RIDGID’s spec line says 3.5 lb, its FAQ says 3.3 lb without batteries, and its ordering table says 4.0 lb. I’d plan on 3.5 lb. The ST-305 is 2.5 lb with batteries.

Both pieces carry RIDGID’s Full Lifetime Warranty. If you only add one thing later, make it the inductive clamp, for lines you can’t clip to.

From RIDGID’s manual: exposing the line is the only way to confirm where it is and how deep. Treat depth readings as estimates.

Pros

  • Hears 512 Hz sondes and 1, 8 and 33 kHz line trace
  • Traces any frequency from 10 Hz to 35 kHz
  • ST-305 sends two frequencies at once
  • Full Lifetime Warranty on both
  • Sold by Amazon.com

Cons

  • No inductive clamp in this bundle
  • RIDGID lists three different SR-20 weights
  • Neither piece lists 262 kHz on the receiver side
  • C cells for both, 10 in all
$3,979.29 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
Check it on Amazon (opens in a new tab)
Spec score
9.5 of 10
Sonde range
10 of 10
Trace frequencies
10 of 10
Battery
8 of 10
Warranty
10 of 10
Key spec
Sonde: 16 Hz–33 kHz
Key spec
Trace: 128 Hz, 1, 8, 33 kHz
Key spec
Transmitter: 25 mA–5 W
Key spec
SR-20: 3.5 lb
Key spec
ST-305: 2.5 lb
Key spec
4 C + 6 C cells
In the kit
SR-20 receiver plus ST-305 5 W line transmitter with leads, clips and ground stake

RIDGID Scout + ST-305: a simpler sonde kit

Best for sonde locates behind a sewer camera

RIDGID NaviTrack Scout locator (19238) with ST-305 line transmitter

The Scout is RIDGID’s sonde specialist. RIDGID says its multi-directional antennas see the whole signal all the time, so there are no nulls or false peaks to fool you. You walk to the strongest signal, and the depth shows when you’re over it.

It reads 512, 640 and 874 Hz and 33 kHz sondes. That covers RIDGID’s 512 Hz 16728 sonde. The micro map marks a pole in front of the sonde and one behind it, which is how you confirm the spot.

RIDGID’s manual is blunt about one thing. Being on the equator line doesn’t mean you’re over the sonde. You need the equator and the strongest signal in the same place. If the yellow marker isn’t about halfway between the two pole markers, the sonde is tilted.

For depth, the manual says to hold the mast within 5 degrees of vertical, take a reading, turn the Scout 180 degrees and read again. If the two aren’t within about 10%, something is distorting the field.

The ST-305 in this bundle is the same 5 W transmitter as in my top pick. The catch is the overlap. The Scout traces at 128 Hz, 8 kHz and 33 kHz. The ST-305 sends 1, 8, 33 and 262 kHz. So with this pair you trace at 8 or 33 kHz only.

That’s fine for most service lines, since RIDGID’s frequency sheet calls 8 kHz a good starting point on a good circuit. It’s a limit on very long runs, where lower frequency carries farther.

Four C cells run it 12 to 24 hours, per RIDGID, or an 18V pack with the SeekTech adaptor. It weighs 3 lb and carries RIDGID’s Full Lifetime Warranty.

If you already own a SeeSnake camera with a sonde in the head, the Scout is the receiver I’d pair with it. My sewer camera with locator guide covers kits that bundle both.

Pros

  • Multi-directional antennas, no nulls or false peaks
  • Map marks both poles of a sonde
  • 12 to 24 hours on four C cells
  • 3 lb
  • Full Lifetime Warranty, sold by Amazon.com

Cons

  • Line trace only at 128 Hz, 8 and 33 kHz
  • Can’t hear the ST-305’s 1 kHz setting
  • No broadband passive scan
  • No clamp in this bundle
$2,652.16 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
Check it on Amazon (opens in a new tab)
Spec score
9.0 of 10
Sonde range
9 of 10
Trace frequencies
8 of 10
Battery
9 of 10
Warranty
10 of 10
Key spec
Sonde: 512, 640, 874 Hz, 33 kHz
Key spec
Trace: 128 Hz, 8, 33 kHz
Key spec
Passive: 50, 60 Hz
Key spec
3 lb
Key spec
4 C cells
Key spec
FCC Class B
In the kit
NaviTrack Scout receiver plus ST-305 5 W line transmitter

TEMPO 551: long runs and tracer wire

Best for long metal runs and tracer wire to 20 ft deep

TEMPO 551 underground locator kit

TEMPO Communications builds the 551 for buried cable and metal pipe. Its datasheet lists electrical, communications and irrigation cables, tracer wire, metallic pipe, fish tape and 33 kHz sondes. It rates the kit for depths past 20 ft and runs over 1 mile.

The transmitter sends 1.75 kHz and 33 kHz at the same time in direct connect. On the receiver you flip between them. TEMPO’s manual says 1.75 kHz goes farthest and bleeds less onto other lines, while 33 kHz works better on short runs and lines in conduit.

There are three ways to put the signal on. Direct connect clips to the pipe and a ground stake. The IC-5 clamp, which is in the kit, wraps around a line at 33 kHz. And the transmitter’s built-in antenna broadcasts 133 kHz into a line you can’t reach.

The receiver has peak and null modes. TEMPO says peak is easy to follow, while null pinpoints the line and finds depth. For depth you tip the receiver to 45 degrees and walk out until the signal nulls. The distance is the depth, and TEMPO says to average both sides.

IntelliTrack is TEMPO’s noise filter for work near power, and the manual says it helps most at 1.75 kHz. Hold the frequency button until an F shows on the screen.

Both pieces are IP54. The transmitter takes six D cells, good for 40 hours in dual mode or 50 in single, per TEMPO. The receiver runs about 35 hours on four AA cells and weighs 1.2 lb.

The full kit is 11.5 lb in a 28 in. hard case. TEMPO backs it with a one-year limited warranty, shorter than RIDGID’s.

It was new and sold by Tempo Communications, the maker, on the day of the update. For pure line tracing, it’s my pick over the RIDGID kits.

Pros

  • Over 1 mile of run and 20+ ft depth, per TEMPO
  • 1.75 and 33 kHz at the same time
  • Inductive clamp in the kit
  • IP54 receiver and transmitter
  • Receiver runs 35 hours on 4 AA

Cons

  • Sondes at 33 kHz only, not RIDGID’s 512 Hz
  • One-year limited warranty
  • 11.5 lb full kit
  • Sold by TEMPO, not Amazon
$1,297.00 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
Check it on Amazon (opens in a new tab)
Spec score
8.0 of 10
Sonde range
7 of 10
Trace frequencies
8 of 10
Battery
10 of 10
Warranty
7 of 10
Key spec
Direct: 1.75 + 33 kHz
Key spec
Clamp: 33 kHz
Key spec
Antenna: 133 kHz
Key spec
Depth 20+ ft
Key spec
Run 1+ mile
Key spec
IP54
In the kit
551 kit: transmitter, receiver, ground stake, IC-5 inductive clamp, hard case

TEMPO 501 Tracker II: shallow lines and wire

A cable and wire locator with no sonde mode, so it sits outside the score.

TEMPO 501 Tracker II receiver and transmitter with its case
TEMPO 501 Tracker II cable locator kit. Product photo: Amazon.

The Tracker II is TEMPO’s simpler kit. TEMPO says it finds the path and depth of buried cable, service wires and metallic pipe or conduit, and finds the end of a cut cable. It rates it to 4,000 ft and 7 ft deep.

Its trick for plastic pipe is in the manual. For PVC or other non-metallic pipe, push a fish tape or plumber’s snake in first, then clip one lead to it and the other to a screwdriver in the ground. The snake carries the signal.

For metal pipe, one lead goes on the pipe and the other to ground. For a gas line, TEMPO says to clip one lead to the IN side of the meter and the other to the OUT side.

Where it does wellWhat to watch
Up to 4,000 ft and 7 ft deep, per TEMPOOne frequency, 447.5 kHz
Inductive coupler and antenna in the kitRated to 7 ft deep
Finds the end of a cut cable and splicesNo sonde mode
Runs on AA and 9V cellsOne-year limited warranty
Sold by TEMPO

The kit has three ways to apply signal. The CS16 leads are an 8 ft pair with clips. The IC1 coupler clamps around a cable up to 3 in. And the case lid holds an inductive antenna that broadcasts into a line you can’t touch.

TEMPO’s manual has a careful note on the antenna. The signal can jump into other utilities, so start the receiver at least 20 ft away, and turn the output down in crowded ground like trailer parks.

It works at one frequency, 447.5 kHz, at up to 140 mW. Depth uses the 45 degree method: mark the line, tilt the receiver to 45 degrees, walk out until the tone dips, and measure.

Power is eight AA cells in the transmitter (about 30 hours) and one 9V in the receiver (about 10 hours). Both shut off after 90 minutes idle. The full kit is 8 lb in a polyethylene case.

TEMPO lists 240 VAC protection on the datasheet and 250 VAC in the manual, and says direct connection to live cable isn’t recommended. It carries a one-year limited warranty and was new from Tempo Communications on the day of the update.

Buy it if: You trace shallow water service, tracer wire or a snake pushed down PVC, and want a simple kit. Skip it if: Your lines run deeper than 7 ft or you need a sonde receiver. Look at the TEMPO 551 or the RIDGID kits.

Comparison only: no exact Amazon offer is qualified for a buy button here. No price is shown for this pick.

RIDGID ST-305 + 16728 sonde: add-on for a receiver you own

An add-on with no receiver, so it sits outside the score.

RIDGID ST-305 line transmitter with the small 16728 sonde
RIDGID ST-305 line transmitter with 16728 512 Hz sonde. Product photo: Amazon.

From RIDGID’s ST-305 manual: attach the ground lead first, and never connect to a line known to be energized.

This is the add-on kit. It has the ST-305 transmitter and RIDGID’s 16728 sonde, and no receiver. It makes sense if a RIDGID receiver is already on the truck.

The 16728 is a small battery sonde, 0.94 in. across and 2.92 in. long, at 3.5 oz with its battery. You tighten the cap to turn it on, and a red LED flashes slowly. A fast flash means the AAA is low. Loosen it 3/4 of a turn to shut it off.

It sends 512 Hz, which RIDGID says any compatible locator can pick up. It threads onto push cable, duct rod or sewer cable with 1/4-20 threads, and RIDGID sells adapters for 3/8 in. through 1-1/4 in. drain cables. RIDGID’s page also says it fits a water jet hose.

Where it does wellWhat to watch
Turns a RIDGID receiver into a line tracerNo receiver in the box
Sonde runs up to 4 hours on one AAASonde reaches 15 ft in cast iron, per RIDGID
Sonde threads onto drain cable or a jetter hoseSonde is 512 Hz only
Full Lifetime WarrantyClamp sold separately
Sold by Amazon.com

Range is where cast iron matters. RIDGID’s manual lists typical range with its NaviTrack receiver as 25 ft in air and 15 ft in cast iron. It names cast iron, ductile iron and wet, salty ground as the usual interference.

Battery life is up to 4 hours on one alkaline AAA, per the product page. The manual narrows it to 3.5 hours at 70 F with the AAA it recommends. Carry spares.

The ST-305 is the same 5 W transmitter as in the two RIDGID kits above. Clip the ground lead first, then the pipe. RIDGID’s manual says never to connect to a line known to be energized, and a warning light comes on above about 62 VAC.

The ST-305 can also work by induction: set it over a line and its internal coils put a 33 kHz signal on the pipe below, no clip needed. RIDGID says lower frequencies couple poorly that way, so it defaults to 33 kHz.

If you only need the sonde, the 16728 is sold on its own too. Both pieces carry RIDGID’s Full Lifetime Warranty and were new from Amazon.com on the day of the update.

Buy it if: You already own a RIDGID SR-20, SR-24 or Scout receiver and want to trace metal lines too. Skip it if: You don’t own a receiver. Buy the SR-20 + ST-305 kit instead.

Comparison only: no exact Amazon offer is qualified for a buy button here. No price is shown for this pick.

The three kits side by side

Tap a number column header to sort on desktop. On a phone, swipe the table sideways.

KitSpec scorePhotoReceiverTransmitterSonde modeRated depth (ft)Receiver battery (h)WarrantyBuy
RIDGID SR-20 + ST-305
Sondes and tracing
9.5RIDGID SR-20 kitSR-20ST-305, 5 W16 Hz–33 kHzNot listed10–15LifetimeCheck it on Amazon
RIDGID Scout + ST-305
Sondes
9.0RIDGID Scout kitScoutST-305, 5 W512–874 Hz, 33 kHzNot listed12–24LifetimeCheck it on Amazon
TEMPO 551
Long runs
8.0TEMPO 551551 receiver551, 3.7 W33 kHz only20351 yearCheck it on Amazon

From RIDGID and TEMPO manuals, datasheets and product pages, read Oct 19, 2026. RIDGID doesn’t publish a maximum depth for the SR-20 or Scout. The 15 ft figure is the 16728 sonde’s typical range in cast iron with a NaviTrack receiver.

What you’re chasing decides the locator

A locator only finds a signal. Metal pipe can carry one from a line transmitter. Plastic pipe can’t, so you send a sonde or a wire down it. Start here.

What’s buriedHow you get a signal on itKits here that do itFrom
Copper, steel or iron water lineClip a line transmitter to the pipe, ground the other leadSR-20, Scout, TEMPO 551, TEMPO 501, ST-305 kitST-305 and TEMPO manuals
Plastic pipe with tracer wireClip the transmitter lead to the tracer wireSame fiveST-305 manual
Plastic drain or sewer, no wirePush a sonde in on a cable, or float itSR-20, Scout (with a 512 Hz sonde)SR-20 and Scout manuals
PVC with no sonde on handPush a fish tape or plumber’s snake in, clip to itTEMPO 501TEMPO 501 manual
Cast iron sewerSonde works, but the signal is weakerSR-20, ScoutRIDGID 16728 manual: 15 ft vs 25 ft in air
Live power cablePassive 50/60 Hz, never aloneSR-20, Scout, TEMPO 551TEMPO 551 manual

Plenty of jobs need two of these rows. A clog in a 4 in. PVC sewer is a sonde job. A copper service line under a driveway is a line trace job. That’s why my top pick does both.

Cast iron is the one to plan around. RIDGID’s 16728 sonde manual lists 25 ft of range in air and 15 ft in cast iron, and both RIDGID manuals say sondes have trouble sending through cast and ductile iron.

Which receiver hears which signal

A transmitter and receiver only work together on a shared frequency. RIDGID’s manual says the transmitter and receiver must be set the same. This chart checks each pairing on this page against the makers’ lists.

SignalComes fromSR-20 hears itScout hears itTEMPO 551 hears it
512 Hz sondeRIDGID 16728YesYesNot listed
1 kHz line traceST-305YesNot listedNot listed
1.75 kHz line traceTEMPO 551Not listedNot listedYes
8 kHz line traceST-305YesYesNot listed
33 kHz line traceST-305, TEMPO 551YesYesYes
33 kHz sondeOther makers’ sondesYesYesYes
133 kHz inductionTEMPO 551 antennaNot listedNot listedYes
262 kHz line traceST-305 (long press)Not listedNot listedNot listed
50/60 Hz powerLive power linesYesYesYes

“Not listed” means the maker’s spec list doesn’t name it. The SR-20 can be set to trace any frequency from 10 Hz to 35 kHz, so it may reach 1.75 kHz as a custom setting; RIDGID doesn’t list it as a preset. The TEMPO 501 works only at its own 447.5 kHz.

Two things fall out of this chart. The Scout and ST-305 pair shares only 8 and 33 kHz, so the 1 kHz setting is wasted with a Scout. And no receiver here lists the ST-305’s 262 kHz, which RIDGID’s frequency sheet calls a last resort anyway.

If you mix brands, check the chart first. The TEMPO 551 doesn’t list RIDGID’s 512 Hz sonde, and RIDGID’s receivers don’t list the 551’s 133 kHz broadcast.

Which frequency to start with

RIDGID’s frequency sheet gives one rule: use the lowest frequency that gives you a traceable signal over the distance you need. TEMPO’s manual says the same thing.

FrequencyGood forWatch out forSource
128 Hz to 1.75 kHzLong runs on a good circuit; stays on the target lineStopped by breaks, gaskets and bad connections; induces poorlyRIDGID frequency sheet, TEMPO 551 manual
8 kHzA good first choice on a direct connectionInduces only weakly to moderatelyRIDGID frequency sheet
33 kHzStubs, dead ends, broken tracer wire, rubber jointsBleeds into the ground and onto nearby linesRIDGID frequency sheet, Scout manual
133 to 262 kHzInduction with no clip point; last resortLights up nearly everything nearbyRIDGID frequency sheet, TEMPO 551 manual

My read: on a copper service line, start at 8 kHz (or 1.75 kHz on the TEMPO 551). If the signal fades before you reach the house, step up to 33 kHz. If you start picking up the gas line next to it, step back down.

The Scout manual adds a fix for a messy trace. Try a lower frequency, move the ground stake away from the line, and check the line isn’t bonded to another utility.

Get the ground right before you blame the locator

RIDGID’s grounding sheet says a better transmitter ground is usually the first thing to fix. Both makers give the same steps.

  1. 1
    Sweep first

    Run a passive sweep before you drive the stake, so you don’t hit another buried line. RIDGID’s grounding sheet says so.

  2. 2
    Set the stake to the side

    TEMPO says 2 to 3 ft off the line’s path, near where it enters the ground.

  3. 3
    Drive it deep

    Deeper reaches moister soil. RIDGID suggests a longer stake, a shovel or a long screwdriver if needed.

  4. 4
    Wet dry ground

    Both makers say to wet dry soil. TEMPO suggests salty water on the stake.

  5. 5
    Clean the clip point

    The ST-305 manual says to scrape off dirt, paint and corrosion before clipping on.

  6. 6
    Ground the far end

    TEMPO says a spare stake at the far end helps most, especially at 1.75 kHz.

  7. 7
    Set the power

    Use only as much current as gives a strong reading. TEMPO aims for 30 to 70% on its meter.

How each kit checks depth

Every manual here says depth is an estimate. Each one also gives a way to check it before you trust it.

RIDGID 16728 sonde, in air25 ftTEMPO 551, line trace20+ ftRIDGID 16728 sonde, in cast iron15 ftTEMPO 501, line trace7 ftRIDGID 16728 sonde, in air25 ftTEMPO 551, line trace20+ ftRIDGID 16728 sonde, in cast iron15 ftTEMPO 501, line trace7 ft
Sources: RIDGID 16728 sonde manual (typical range with a NaviTrack receiver), TEMPO 551 datasheet, TEMPO 501 datasheet, read Oct 19, 2026.
KitHow it reads depthHow to check the reading
RIDGID SR-20Continuous, on screenRaise the receiver about 6 in.; depth should rise about 6 in.
RIDGID ScoutShows when you’re over the targetRead, turn 180 degrees, read again; within about 10%
TEMPO 55145 degree null methodDo both sides of the line and average them
TEMPO 50145 degree tone-dip methodMark over the line, then where the tone dips

RIDGID’s manuals say exposing the line is the only way to verify its location and depth, and to recheck depth while you dig. Follow your local one-call rules before any excavation.

Finding a sonde in a drain, step by step

These steps come from RIDGID’s SR-20 and Scout manuals. They work with any RIDGID receiver on this page.

  1. 1
    Test before it goes in

    Turn the sonde on and make sure the receiver hears it on the same frequency, set to sonde mode, not line trace.

  2. 2
    Start short

    Push it about 15 ft in first if you don’t know which way the pipe runs.

  3. 3
    Sweep for direction

    Hold the mast out and sweep it. The signal peaks when the mast points toward the sonde.

  4. 4
    Walk to the peak

    Follow the rising signal and tone. Then move the receiver every way to be sure it drops off on all sides.

  5. 5
    Mark both poles

    Find the pole in front and the pole behind. The sonde sits about halfway between them.

  6. 6
    Check depth

    Take the reading with the mast vertical, then check it the way your receiver’s manual says.

  7. 7
    Expect less from cast iron

    Unequal pole distances can mean a tilted sonde or a change from cast iron to plastic.

What you carry across the yard

You walk the whole line with the receiver in one hand. Here’s what each maker lists for the receiver.

RIDGID SR-203.5 lbRIDGID NaviTrack Scout3 lbTEMPO 551 receiver1.2 lbRIDGID SR-203.5 lbRIDGID NaviTrack Scout3 lbTEMPO 551 receiver1.2 lb
Sources: RIDGID SR-20 and Scout product pages, TEMPO 551 datasheet, read Oct 19, 2026.

The RIDGID receivers are heavier because of the tall mast with antennas at both ends. That mast is how they compare signal top and bottom to work out depth and draw the map.

The TEMPO 551 receiver is a wand at 1.2 lb with batteries. Its transmitter is the heavy piece at 4.3 lb, but it sits at the hookup while you walk.

Safety rules from the manuals

These come straight from the RIDGID and TEMPO manuals. They apply to any locator.

RuleManualWhy the maker gives it
Never connect to a line known to be energizedRIDGID ST-305Shock risk; the warning light trips above about 62 VAC
Attach the ground lead firstRIDGID ST-305Gives unknown voltage a path away from you
Don’t trust a passive sweep aloneTEMPO 551A balanced power cable can show no field
Expose the line to confirm itRIDGID SR-20 and ScoutThe only way to verify location and depth
Treat depth as an estimateRIDGID and TEMPOFields get distorted by nearby metal and tees
Don’t hit a utility with the ground stakeRIDGID grounding sheetSweep the stake spot first
Follow local one-call rulesRIDGID Scout and ST-305Several utilities may share the area

Where the pages, manuals and listings disagree

I read each maker page, manual and Amazon listing on the same day. These are the spots that don’t match, and the number I’d plan on.

ItemOne source saysAnother saysWhat I’d plan on
SR-20 weightSpec line: 3.5 lbFAQ: 3.3 lb without batteries; ordering table: 4.0 lb3.5 lb
SR-20 kit contentsRIDGID kit 46918: SR-20, ST-305, 4 in. clampThis Amazon bundle: SR-20 and ST-305No clamp
ST-305 weightManual: 2.5 lb (1.1 kg)RIDGID ordering table: 2.5 lb, 1.9 kg2.5 lb
16728 battery lifeProduct page: up to 4 hoursManual: 3.5 hours at 70 F3.5 hours
TEMPO 501 voltage protectionDatasheet: 240 VAC, 500 VDCManual: up to 250 VACDon’t connect to live lines
TEMPO 551 depthDatasheet: 20+ ftAmazon listing: 20 ft20 ft

None of these changes the picks. The one to act on is the clamp. If you want RIDGID’s inductive clamp, it’s a separate purchase with this bundle, and it was low in stock on the day of the update.

Which kit for the work you do

Your workPickWhy
Sondes in drains plus metal water linesRIDGID SR-20 + ST-305Widest receiver list on this page
Mostly sonde locates behind a cameraRIDGID Scout + ST-305Sonde-first screen, 12 to 24 h batteries
Long metal runs, tracer wire, irrigation wireTEMPO 551Over 1 mile, 20+ ft, clamp in the kit
Shallow service lines, snake in PVCTEMPO 501 Tracker IISimple single-frequency kit to 7 ft
You own a RIDGID receiver alreadyRIDGID ST-305 + 16728Adds tracing and a sonde
Finding the clog itself on cameraSee my sewer camera with locator guideCameras with a sonde in the head

My call from the makers’ documents. The picks rest on the makers’ published specs and manuals.

One receiver for both jobs

If you’ll chase sondes and metal pipe, buy a receiver that lists both. Of these, the SR-20 lists the most frequencies.

Matched pairs

The TEMPO kits are built as pairs. Their receivers hear their own transmitters, and that’s what TEMPO rates.

Mixing brands

Check the frequency chart first. A TEMPO 551 doesn’t list 512 Hz, the frequency of RIDGID’s 16728 sonde.

Questions people ask

What is the best pipe locator?

My call is the RIDGID SR-20 with the ST-305 transmitter, because it does both sonde locates and metal line tracing. For long runs of metal pipe or tracer wire, the TEMPO 551 lists over a mile and 20+ ft of depth.

What is the best cable and pipe locator?

For cable and metal pipe together, the TEMPO 551. TEMPO lists electrical, communications and irrigation cable, tracer wire and metallic pipe, with an inductive clamp in the kit and IntelliTrack for noise near power.

Can a pipe locator find PVC pipe?

Not on its own. PVC can’t carry a signal, so you put one in it. Push a sonde in on a cable, clip to a tracer wire if there is one, or, as TEMPO’s 501 manual says, push in a fish tape or snake and clip to that.

How deep can a pipe locator find a pipe?

TEMPO rates the 551 past 20 ft and the 501 to 7 ft. RIDGID lists its 16728 sonde at 25 ft in air and 15 ft in cast iron with a NaviTrack receiver. Every maker says depth is an estimate.

Can you locate a cast iron sewer line?

Yes, with a sonde inside it, but expect less range. RIDGID’s sonde manual lists 15 ft in cast iron against 25 ft in air, and its receiver manuals say sondes have trouble sending through cast and ductile iron.

Do I need a transmitter to find a water line?

To trace a specific metal line, yes. A line transmitter puts a known signal on it. A passive sweep picks up power and radio signals on lines, but TEMPO warns never to rely on passive alone.

What frequency should I use?

RIDGID’s rule is the lowest frequency that gives a traceable signal over your distance. Its frequency sheet calls 8 kHz a good start on a direct connection, with 33 kHz for broken tracer wire and dead ends.

Can I use a TEMPO locator to find a RIDGID sonde?

Not the 16728. It sends 512 Hz, and TEMPO lists the 551 for 33 kHz sondes. The 501 works only at 447.5 kHz.

Is there an app that finds underground pipes?

Every kit on this page works the same way: a receiver hears a transmitter or sonde signal. RIDGID says exposing the line is the only way to confirm it.

Can I rent a pipe locator?

I only checked new kits for sale, so I can’t speak to rental stock. If you rent, check the receiver’s frequency list against the sonde or transmitter you’ll use.

How I picked these

Why trust me

I’m Isaac Daniels, a licensed journeyman plumber in Georgia (license #JP507711). Every number here comes from RIDGID and TEMPO documents, read the same day.

How I pick

  • Only genuine brand kits, new and in stock on the day of the update.
  • Frequencies, depth and battery figures from the makers’ manuals, datasheets and spec pages.
  • Pairings checked against each receiver’s published frequency list.
  • A spec score from four checks in the makers’ documents, shown below: sonde range, trace frequencies, battery life and warranty.
  • Where two sources disagree, I say so and plan on the safer number.
  • Prices are read from Amazon with the time shown, never typed in.
  • Recalls checked on cpsc.gov.

The spec score, check by check

Each check scores 0 to 10 and counts one quarter. It’s my score from RIDGID’s and TEMPO’s manuals and datasheets, not a customer rating or a field test. Depth isn’t in it: RIDGID publishes no depth limit for the SR-20 or Scout, so a depth check would score a missing number, not the receiver.

Check (weight)How it’s scored
Sonde range (¼)Sonde frequencies the receiver hears, per the maker: 10 for a continuous range covering 512 Hz and 33 kHz; 9 for four or more set frequencies including both; 7 for one frequency
Trace frequencies (¼)Line-trace frequencies, per the maker: 10 when the receiver traces any frequency across a range; 8 for three set frequencies; 7 for two
Battery (¼)Receiver battery life at the maker’s top figure: 10 for 30 hours or more; 9 for 20 to 29; 8 for 15 to 19; 7 under 15
Warranty (¼)Warranty: 10 for RIDGID’s Full Lifetime Warranty; 7 for a one-year limited warranty
TotalAverage of the checks, to one decimal
PickSonde rangeTrace frequenciesBatteryWarrantyScore
RIDGID SR-20 + ST-30510108109.5
RIDGID Scout + ST-305989109.0
TEMPO 551781078.0

Recall check, Oct 19, 2026: no CPSC recalls found for pipe, cable or utility locators. RIDGID’s recalls on record are for nailers, vacuums, table saws and ladders. No TEMPO Communications recalls were listed.

Also checked: the RIDGID SR-24LE and ST-510 showed a later ship date. RIDGID’s inductive clamp, the 18V ST-305R and the Scout Pal were low in stock or had a lead time. Milwaukee’s locator listings were a look-alike or out of stock, and General’s Gen-Eye locator had a lead time. Unbranded 512 Hz receivers had no maker documents to check, and electrical circuit tracers aren’t pipe locators.

Sources

Related guides