Garbage disposal splash guard replacement

For garbage disposal splash guard replacement, I match the model first: QCB-AM for Evolution, the Badger upgrade kit, or Waste King 1025 for EZ Mount.

As an Amazon Associate I earn from qualifying purchases. Disclosure

In my 7 years of experience, these are the products I'd install.

InSinkErator Badger baffle upgrade kit
InSinkErator Badger baffle upgrade kit. Product photo from Amazon.

The short answer

Choose InSinkErator QCB-AM for an Evolution Quiet Collar and BUK-00 to upgrade a Badger. A Waste King EZ Mount takes 1025. Match Moen by model, and cut the power first.

Evolution Quiet Collar
Check QCB-AM against the full model.
Badger conversion
BUK-00 / 78529-ISE, with the initial conversion instructions.
Waste King EZ Mount
1025, after confirming the guard is in the package.
Built-in or unidentified guard
Keep the mount attached and confirm the service route.
Find the replacement route for your model

Find your replacement route

I start with the full model on the disposal label. This finder cannot replace the model instructions or an in-person check.

Read the model label before pulling the guard. Disconnect electrical power before handling it.

Replacement guards by disposal family

Choose the part for your model, rather than a diameter from a generic listing. Quiet Collar, the Badger kit and Waste King’s 1025 each fit a different disposal family. A Moen owner should use the model chart below before ordering.

InSinkErator Antimicrobial Quiet Collar Sink Baffle QCB-AM (Evolution Series)

Product photo from Amazon.

For Evolution Quiet Collar fit

Quiet Collar for Evolution

$9.49 at Amazon
Buy QCB-AM on Amazon
Price as of Nov 18, 2026, 1:30 AM EST

New · Sold by AM Incorporated

INSINKERATOR BADGER Disposal Baffle Upgrade Kit, BUK-OO

Product photo from Amazon.

For a Badger baffle upgrade

Badger baffle upgrade kit

$16.49 at Amazon
Buy the Badger kit on Amazon
Price as of Nov 18, 2026, 1:30 AM EST

New · Sold by Amazon.com

Waste King 1025 EZ Mount splash guard and sink stopper

Product photo from Amazon.

For a Waste King EZ Mount

Waste King 1025

$8.46 at Amazon
Buy Waste King 1025 on Amazon
Price as of Nov 18, 2026, 1:30 AM EST

New · Sold by Amazon.com

Scroll across the table to see every column.

PartKey specsPick it ifSkip it if
Quiet Collar for EvolutionQCB-AM, Maker part 74653D, Removable baffle, Evolution product-page fitYour disposal documentation calls for the Quiet Collar QCB-AM and your existing baffle arrangement matches it.You have a Badger, a Waste King mount or an unidentified Moen. Confirm specialty or lighted baffles with the maker before substituting.
Badger baffle upgrade kitBUK-00 maker model, 78529-ISE maker part, Badger baffle upgrade, Removable after conversionYou have a Badger and want the maker’s removable-baffle upgrade, with the package identity and installation instructions confirmed.You need an Evolution Quiet Collar, or you cannot establish the correct conversion procedure for your Badger model.
Waste King 10251025, EZ Mount; listing describes guard and stopper, with a neoprene stopperYour Waste King or Whirlaway has the EZ Mount and its guard lifts out.You have a Professional 3-Bolt mount, where Waste King says the guard is built in.

Each part fits a different disposal arrangement: QCB-AM the Evolution Quiet Collar, BUK-00 the Badger conversion and 1025 the Waste King EZ Mount. The model and the maker part number decide.

Sources for this section: 1, 2, 5, 7

When the disposal is an Evolution

Each guard fits one disposal family, so the model decides, with no score.

InSinkErator Antimicrobial Quiet Collar Sink Baffle QCB-AM (Evolution Series)
Quiet Collar for Evolution. Product photo: Amazon.

QCB-AM is the Quiet Collar model to check when an Evolution disposal needs its removable sink baffle replaced. InSinkErator identifies the accessory as part 74653D. The useful starting point is that maker reference, rather than a store photograph of a black rubber insert.

The Evolution product page says the baffle is removable for cleaning and helps reduce sound. Those are maker descriptions, not measured improvements promised here. No decibel figure tells you how much quieter your particular sink will become after replacing a worn guard.

Badger is the exclusion that matters most. InSinkErator expressly says this Quiet Collar is not for Badger disposers. An InSinkErator badge on the disposal does not settle the fit. A Badger owner should check the Baffle Upgrade Kit instead of forcing QCB-AM into the opening.

Where it does well

  • Maker identifies Evolution use
  • Removes for cleaning
  • Maker gives a press-to-seat instruction
  • Part reference 74653D is documented

What to watch

  • Maker expressly excludes Badger
  • Power and Advanced fit still needs a model check
  • No measured noise reduction claimed

There is also a naming difference in the maker literature. The current accessories catalog lists QCB-AM for Power and Advanced Series disposals, while the product page names Evolution. I would confirm the individual disposal manual, especially when its original baffle has a specialty feature.

For Evolution installation, InSinkErator says to press the Quiet Collar into the sink opening until it snaps into place. Disconnect electrical power before handling the guard. The instruction describes seating a matching part; it does not authorize cutting, trimming or changing the sink flange.

The New QCB-AM offer is sold by AM Incorporated and was in stock when I checked on Nov 18, 2026, 1:30 AM EST. I confirm the listing model and condition at checkout; the maker documents establish the fit.

Choose QCB-AM when the disposal calls for it and the existing removable arrangement matches. If the old guard will not release as its manual describes, leave the mounting assembly alone. Confirm the model before turning a guard purchase into a disposal removal job.

I match QCB-AM by model, then check the package reference: the current maker catalog lists 74653D, while the Amazon product record gives 77960A. I do not treat those part numbers as interchangeable without confirmation from InSinkErator.

Sources for this section: 1, 2, 3

The Badger baffle upgrade kit

INSINKERATOR BADGER Disposal Baffle Upgrade Kit, BUK-OO
Badger baffle upgrade kit. Product photo: Amazon.

InSinkErator describes its Baffle Upgrade Kit as a way to give a Badger a removable baffle for cleaning. The catalog calls the model BUK-00 and identifies part 78529-ISE. This is the Badger route; it is not the same accessory as the Evolution Quiet Collar.

The maker lists upward food and water splash control among the kit’s purposes. It also describes noise muffling and easy removal for cleaning. Those benefits explain why a Badger owner might choose the conversion, but they do not establish a measured sound reduction or a drainage improvement.

The word upgrade matters. Removing a baffle after a conversion and performing the initial conversion are separate jobs. The maker’s product description establishes the result, but it does not give enough detail to substitute for the kit’s installation sheet. Obtain that sheet before starting work.

Where it does well

  • Maker identifies Badger use
  • Converts to a removable cleaning baffle
  • Designed to contain upward splash
  • Maker identifies part 78529-ISE

What to watch

  • Initial conversion sheet still needed
  • Listing writes BUK-OO; maker writes BUK-00
  • Not the Evolution Quiet Collar

Do not pull harder on a fixed Badger baffle because the new kit is described as removable. First establish which arrangement is already installed. If your repair requires loosening the disposal mount, have a service professional handle the work with the unit supported and electrical power disconnected.

The Amazon listing title ends in BUK-OO, with letters, while InSinkErator’s catalog uses BUK-00, with zeros. The offer is presented as the InSinkErator branded Badger kit. Confirm 78529-ISE on the package and the maker’s fit information before beginning the conversion.

The New Badger kit offer is sold by Amazon.com and was in stock when I checked on Nov 18, 2026, 1:30 AM EST. I confirm the package reference and follow the kit instructions for the conversion.

Use the Badger kit when removable cleaning access is your aim and its instructions match the disposal. Keep the power off during service. If you only have odor on an intact guard, establish the permitted cleaning method before committing to a conversion.

Sources for this section: 1, 2

Waste King 1025 for an EZ Mount

Waste King 1025 EZ Mount splash guard and sink stopper
Waste King 1025 splash guard and stopper. Product photo: Amazon.

1025 is the part Waste King itself names for this job. Its FAQ says an EZ Mount owner can buy a replacement splash guard, the EZ Mount Splash Guard & Stopper, item 1025, on Amazon. The linked listing carries the Waste King name, part number 1025 and Moen Incorporated as the manufacturer.

Fit comes from the mount, not the motor size. Waste King’s FAQ says the EZ Mount guard is removable and can go in the dishwasher, while the Professional 3-Bolt guard is built in. I use those model-specific access instructions before choosing a replacement. The Amazon 1025 listing describes a neoprene stopper; that is not proof of the guard material.

The part numbers need one check. The L-2600 parts drawing, Rev. 9/21, lists 1025 as the drain stopper only and 1027 as the stopper and removable splash guard pack. The current FAQ and Amazon 1025 listing describe a guard and stopper. I confirm the package includes the slotted guard before treating it as a replacement, rather than relying on the number alone. Source

Where it does well

  • Waste King’s FAQ names 1025 for EZ Mount
  • Guard and stopper in one listing
  • Lifts out; dishwasher cleaning allowed
  • 1025 listing describes a neoprene stopper

What to watch

  • L-2600 drawing calls 1025 the stopper only
  • Not for a Professional 3-Bolt mount
  • Confirm package contents for the exact disposal model
  • Confirm the mount on the bottom label first

Before you touch the guard, switch the disposal off and unplug it or shut off its circuit, as Moen’s odor answer describes. Waste King’s FAQ treats the EZ Mount guard as removable, so it should come out by hand. Seat the new one the way the old one sat, then run water before you restore power and check below the sink for drips.

If the old guard won’t come out, stop. Waste King says Professional 3-Bolt guards are built in, and the model label on the bottom of the disposal tells you which mount you have. The New 1025 offer was in stock from Amazon.com on Nov 18, 2026, 1:30 AM EST.

Sources for this section: 5, 7, 10

Compare the three replacement routes

Scroll across the table to see every column.

Part and photoUseMaker referenceMain advantageLimitOffer
InSinkErator Antimicrobial Quiet Collar Sink Baffle QCB-AM (Evolution Series)InSinkErator Antimicrobial Quiet Collar Sink Baffle QCB-AM (Evolution Series)Evolution Quiet Collar replacementQCB-AM / 74653DRemovable for cleaningNot for BadgerCheck price on Amazon
INSINKERATOR BADGER Disposal Baffle Upgrade Kit, BUK-OOINSINKERATOR BADGER Disposal Baffle Upgrade Kit, BUK-OOBadger removable-baffle upgradeBUK-00 / 78529-ISEChanges cleaning accessInitial kit instructions requiredCheck price on Amazon
Waste King 1025 EZ Mount splash guard and sink stopperWaste King 1025 EZ Mount splash guard and stopperWaste King EZ Mount replacement1025 (Waste King FAQ)Lifts out; dishwasher cleaning allowedNot for Professional 3-BoltCheck price on Amazon

A torn Quiet Collar on an identified Evolution and a fixed baffle on a Badger are different repairs. Use the first row to replace an existing matching insert. Use the second row to investigate a Badger conversion, and the third for a lift-out Waste King EZ Mount guard. The parts are not alternatives chosen by appearance or seller.

Sources for this section: 1, 2, 5, 7

Find your guard without taking the disposal down

Read the disposal label first. Record the full model, then use its parts drawing to confirm the reference. Waste King locates its model and serial information on the bottom label; a sink drain’s appearance is not a model identifier.

Read the full disposal model Match its parts drawing before touching the guard. RemovableBadger upgradeBuilt-in or unsure Quiet Collar,EZ Mount ordocumented MoenUse model instructions BUK-00 kit78529-ISEGet the conversionsheet before work Pro 3-Bolt guardor unknown modelKeep mount attachedAsk for service route Disconnect electrical power before handling a guard. Keep hands outside the chamber. Uncertain supply: call an electrician. Read the full disposal model Match its parts drawing before touching the guard. Documented removable guard Quiet Collar, EZ Mount or Moen: use the exact model’s removal and seating instructions. Badger baffle upgrade BUK-00 / 78529-ISE: get the conversion instructions before starting the first install. Built-in or unidentified guard Professional 3-Bolt or unknown: keep the mount attached. Ask for the supported service route. Disconnect electrical power before handling a guard. Keep hands outside the chamber. Uncertain supply: call a qualified electrician.
Decision route based on the InSinkErator accessory pages, Waste King FAQ and Moen illustrated parts sheets. This is an access guide, not a dimensioned assembly drawing.

Scroll across the table to see every column.

Disposal family/modelOEM referenceRemoval/accessExclusion or uncertaintySource
InSinkErator EvolutionQCB-AM / 74653DRemovable Quiet Collar; press to seatNot for Badger; confirm the individual modelQuiet Collar page; installation step 12
InSinkErator Power / AdvancedQCB-AM / 74653D in catalogFollow individual model instructionsCatalog family description is not every model’s fit approvalP511-26A, p. 4
InSinkErator BadgerBUK-00 / 78529-ISEUpgrade to removable baffleInitial conversion sheet requiredBaffle Upgrade Kit page; P511-26A
Model expressly calling for RSB-00RSB-00 / 08302DTool-free removable accessoryMaker excludes Evolution/E606; catalog excludes AdvancedRSB product page; P511-26A
Waste King EZ Mount / L-26001025 (FAQ); drawing lists 1027Removable guardCheck the 1025 box holds guard and stopperFAQ; L-2600PT, p. 1
Waste King Professional 3-BoltAsk for model-specific service referenceBuilt-in guardNot a lift-out replacementWaste King mount FAQ
Moen GXP33c / GXP50c205497Removable guardMatch model and revisionEXP11982PT, p. 1
Moen EX50c / EX75c205497Removable guardSheet covers these named modelsEX50CPT, p. 1
Moen EX100C205497Removable guard on the named model drawingUse the current model drawing, not a neighboring modelMoen EXP12254CPT

If your model is missing from the chart, stop at identification. A nearby model name can lead to the wrong mounting arrangement. Ask the maker for the current part number using the full model and serial information. Keep that answer with the disposal manual for the next replacement.

A seller’s list of brands does not establish an OEM fit. For example, Quiet Collar and Badger are both InSinkErator products, yet the Quiet Collar page excludes Badger. Apply the same model-first check when a generic listing names Moen and Waste King together.

Sources for this section: 1, 2, 5, 7, 8

A baffle, gasket and stopper do different jobs

Scroll across the table to see every column.

PartWhere to identify itWhat it does for this repair
Splash guard / baffleMoen A1 in INS10477CRemovable guard above the disposal chamber on the documented arrangement
Sink flangeMoen B in INS10477CSeparate sink connection; do not loosen it for a confirmed lift-out guard
Fiber gasketMoen C in INS10477CSeparate mounting component, not another name for A1
StopperMoen A in INS10477CCloses the sink opening; confirm it separately from the splash guard

Moen’s instruction sheet separates the removable guard from the sink flange and fiber gasket. That distinction prevents a common wrong purchase: a rubber part visible from above is not proof that it seals the entire mounting assembly below the sink. Identify the failed component before ordering.

If water is dripping into the cabinet, inspect where it begins while keeping power isolated. A replacement baffle is not a diagnosis of an under-sink leak. A flange or outlet connection needs its own repair route. Do not add sealant around a guard to compensate for an unidentified drip.

A stopper and splash guard can be packaged together, as the Waste King references show, but their names still describe different pieces. When you need the flexible guard, check the package contents expressly. A listing that supplies only a drain stopper will not replace the missing baffle.

Sources for this section: 9

InSinkErator fit depends on the series

Scroll across the table to see every column.

Your documentation saysPart routeBefore you order
Evolution Quiet CollarQCB-AM / 74653DMatch the removable arrangement
Badger baffle upgradeBUK-00 / 78529-ISEGet the conversion sheet
RSB-00 removable sound baffle08302DPositive model fit required; exclusions alone are insufficient
Power or AdvancedQCB-AM appears in current catalogRead the specific disposal manual

Start with the series name on the InSinkErator disposal. Quiet Collar is documented for Evolution on the product page. The catalog uses Power and Advanced Series wording for the same QCB-AM reference. Those descriptions support checking the part, but they do not erase differences between individual models.

RSB-00 is another removable accessory with its own exclusions. The product page rules out Evolution and E606, and the current catalog rules out Advanced. That does not prove it fits every other disposal. Choose RSB-00 only when the actual model documentation or maker confirms the match.

For a Badger, the first question is whether its original baffle arrangement remains or an upgrade kit is already installed. The BUK-00 product page describes conversion to a removable baffle. It does not justify treating an untouched Badger as a Quiet Collar lift-out installation.

Sources for this section: 1, 2

Waste King fit depends on the mount

Scroll across the table to see every column.

MountGuard accessWhat to do
EZ MountRemovableConfirm the part and package; maker references conflict
Professional 3-BoltBuilt inAsk for the model-specific service route
Mount unknownAccess unknownRead the bottom label and the model manual before pulling

Waste King distinguishes EZ Mount and Professional 3-Bolt guards directly in its FAQ. EZ Mount has a removable guard; Professional 3-Bolt has a built-in one. If the guard resists lifting, do not use that resistance as a reason to pry harder. Confirm which mount your model uses.

The ordering problem is separate from access. Waste King’s odor FAQ calls 1025 an EZ Mount splash guard and stopper. The L-2600 parts drawing calls 1025 a stopper alone and 1027 a stopper and removable-guard pack.

The current Waste King FAQ directs EZ Mount owners to 1025 on Amazon, while the L-2600 drawing identifies the guard-and-stopper pack as 1027. I keep both references visible. A page or listing number alone cannot settle the package contents: confirm that the correct slotted guard and stopper are supplied for the disposal model.

A built-in Professional 3-Bolt guard is a service question. Waste King saying it is not removable does not prove no service component exists. Keep the full model available and ask which repair is supported. Do not cut the old baffle away or loosen the mount to experiment.

Waste King permits dishwasher cleaning for an EZ Mount removable guard. Its FAQ specifically says the Professional 3-Bolt guard is not removable. Cleaning permission does not change the access design.

Sources for this section: 5, 7

Why the drain diameter cannot settle fit

Scroll across the table to see every column.

Waste King descriptionApproximate dimensionWhat the number identifies
EZ Mount drain3⅛ inches SourceDrain width in mount comparison
Professional 3-Bolt drain3 3/8 inches SourceDrain width in mount comparison
Typical sink hole3½ inches SourceSink opening, not the replacement guard diameter

Waste King publishes these three dimensions for different purposes. A typical sink hole dimension does not identify the rubber insert, and a drain width does not establish its retaining shape. Use the numbers to understand the maker’s descriptions, then return to the model and part number for ordering.

This is why a generic listing’s diameter can be misleading beside an OEM part. Even an apparently similar opening does not override the built-in guard on a Professional 3-Bolt disposal. I would not trim rubber, enlarge slits or stack a second insert to make an unconfirmed replacement fit.

Sources for this section: 5

Moen fit depends on the exact model

Scroll across the table to see every column.

Models named on sheetGuard referenceDocumentLimit
GXP33c / GXP50c205497EXP11982PT, Rev. 03/23These two models
EX50c / EX75c205497EX50CPT, Rev. 11/21These two models
EX100C205497EXP12254CPTDrawing expressly names EX100C

Moen’s GXP33c/GXP50c and EX50c/EX75c parts drawings identify removable guard 205497. The model names on those sheets are the useful boundary. They support those applications; the separate EXP12254CPT drawing now establishes the same guard reference for EX100C. I use the drawing that actually names the disposal, rather than matching by appearance.

I now use the current EX100C product page’s linked EXP12254CPT drawing. It expressly names EX50C and EX100C and identifies removable splash guard 205497. An older store-page reference to 1016 does not override this model-specific drawing. I still match the model and revision before ordering.

Moen’s general cleaning article also mentions a 1025 guard and stopper. Use its cleaning instructions for an identified removable guard, but use the model’s parts drawing for ordering. A general maintenance article and an exact-model drawing answer different questions.

Sources for this section: 8, 9

Where listings and maker documents disagree

Scroll across the table to see every column.

ReferenceListing or general pageMaker model evidenceDecision
Badger kit nameAmazon title: BUK-OOP511-26A: BUK-00 / 78529-ISEMatch the maker number on the package; the title spelling differs
Quiet Collar familyAmazon title: Evolution SeriesProduct page: Evolution; catalog: Power/AdvancedCheck actual model; never substitute for Badger
Waste King 1025Amazon and FAQ: guard and stopperL-2600PT: 1025 stopper; 1027 guard/stopper pack. Current FAQ: 1025 guard and stopper. Package confirmation required.FAQ points to 1025 on Amazon; check both pieces are in the box
Moen general 1025 referenceCleaning article mentions 1025GXP/EX drawings name 205497 for specified modelsOrder by the exact model drawing

For the Badger kit, ask for the maker part reference rather than resolving letter O versus zero by guesswork. For Waste King, ask specifically whether the package includes a splash guard for your model. The right answer must settle the contents as well as the product name.

For Moen, keep the model-specific drawing in view when reading general maintenance advice. A correct cleaning procedure does not establish universal parts compatibility. If the current maker answer differs from an older drawing, save that answer with the model and revision it covers.

Sources for this section: 2, 5, 7, 8

Clean an intact removable guard before replacing it

Scroll across the table to see every column.

What you findFirst routeReplacement decision
Buildup on an intact, identified removable guardIsolate power and follow the maker’s cleaning methodReassess the guard after cleaning
Torn or missing guardIdentify model and OEM referenceReplace with the matching part
Slow drainage or persistent odorCheck drainage as well as guard buildupDo not assume a new baffle fixes the drain
Fixed guardKeep it attachedUse model-specific cleaning or service advice

Moen identifies two possible odor sources: poor drainage and buildup on the splash guard. That gives you a useful fork. An intact removable guard with deposits is a cleaning candidate. A sink that still drains poorly needs attention beyond replacing the rubber insert.

Disconnect the disposal’s electrical power before touching a removable guard. Moen says to unplug a corded unit or isolate a hardwired unit at the electrical box. Keep hands out of the disposal chamber. If you cannot identify and isolate the supply safely, call a qualified electrician.

Moen permits dishwasher cleaning of its removable guard, and Waste King permits that route for EZ Mount. Do not extend those permissions to every rubber accessory. Check the cleaning instructions for the actual guard, especially if its disposal uses a different baffle arrangement.

For a Moen removable guard, the maker’s hand-cleaning sequence is power off, remove, clean, rinse, reinstall, then restore power. Follow its current cleaning directions for the model. No mixed-cleaner recipe or solvent treatment is needed for this decision.

Sources for this section: 5, 10

Replace a documented lift-out guard safely

  1. 1
    Identify the model and access

    Match the disposal label to its instructions. Confirm that the guard is removable from above. Do not use these steps to convert a fixed Badger baffle or remove a Professional 3-Bolt guard.

  2. 2
    Disconnect electrical power

    Moen directs unplugging a corded disposal or turning off hardwired power at the electrical box before guard removal. InSinkErator directs power off before service. If isolation or grounding is uncertain, have an electrician handle it.

  3. 3
    Remove only the documented insert

    Follow the model’s lift-out instruction with hands kept outside the chamber. Moen prohibits putting hands inside the disposal. Use suitable long tongs or pliers for a loose object, with power still isolated.

  4. 4
    Check the part and clean its seat

    Compare the replacement’s maker reference with the model instructions. Follow the maker’s cleaning directions for the removable guard and accessible seating area. Stop if the retaining surface or mount looks damaged.

  5. 5
    Seat the matching replacement

    For Evolution Quiet Collar, InSinkErator says to press the baffle into the sink opening until it snaps into place. Other models need their own seating instructions. Do not cut a replacement or add a second guard to force a fit.

  6. 6
    Inspect before restoring power

    Make sure the guard is properly seated and all tools are clear. If any plumbing was disconnected, complete the model’s leak test before reconnecting power. Stop for leaks, damaged wiring or an uncertain mount.

For a confirmed lift-out replacement, the disposal stays attached beneath the sink. If your next move would be to loosen a mounting ring or disconnect a drain, stop and check the instructions again. You may have crossed from insert replacement into a different repair.

InSinkErator’s press-until-seated instruction applies to the Evolution Quiet Collar. It is not a tool procedure for every rubber guard. A replacement that will not seat under its own model instructions needs a fit check, rather than extra force against the sink flange.

Sources for this section: 3, 9, 10

A built-in guard needs a different repair

Badger conversion

Obtain the BUK-00 package instructions before work. A removable result does not establish the initial conversion procedure.

Waste King Professional 3-Bolt

The maker calls the guard built in. Ask for the supported service procedure for the exact model.

The mount would need releasing

Disconnect power and stop. Moen warns the disposal can fall when the lower mounting ring is disconnected. Have a service professional support and repair the unit.

A built-in baffle should not be cut away to imitate a lift-out design. The conversion question is whether the maker supplies an approved route for the particular disposal. For a Badger, investigate the documented Baffle Upgrade Kit. For a Waste King Professional 3-Bolt, ask for model-specific service advice.

Moen’s installation instructions warn that a disposal can fall when its lower mounting ring is released. That is why disposal removal belongs beyond this lift-out procedure. A rubber guard purchase is not a reason to improvise support while disconnecting a heavy appliance under the sink.

Sources for this section: 2, 5, 9

Check seating and leaks before restoring power

Scroll across the table to see every column.

Check with power isolatedAcceptable resultIf it fails
Guard seatingMatching part sits as its model instructions showRecheck fit; do not force or trim
Tools and loose objectsAll tools removed; chamber checked without reaching insideUse suitable tongs or seek service
Disturbed plumbingPasses the exact model’s leak testLeave power off and correct the leak
Electrical connectionUndamaged, correctly grounded arrangementCall a qualified electrician

InSinkErator’s installation directions put the leak inspection before the electrical operation test. Check the flange, dishwasher connection, tailpipe and mounting connections when those joints have been disturbed. Its Badger manual describes filling the sink, releasing the stopper and looking underneath as the water drains.

Keep the electrical supply disconnected during that inspection. A visible drip means the job needs attention before operation. Do not smear putty around the rubber guard: the Badger manual restricts plumber’s putty to the sink flange and warns against thread sealant or pipe dope on other disposal connections.

Sources for this section: 3, 9

Check an older disposal for the recall

Certain Anaheim and Moen disposals

CPSC recall 17-129, dated April 11, 2017, includes specified Waste King and Moen models and serial ranges. Check both identifiers against the full CPSC table. Source

A guard is not the recall remedy

CPSC describes a metal component that can escape during use. Stop using an affected disposal and follow the replacement remedy. A new rubber baffle does not complete that repair.

Electrical uncertainty or damage

Leave the disposal disconnected if wiring, grounding or isolation is uncertain. Moen directs unfamiliar users and grounding questions to a qualified electrician.

The recall includes certain Waste King 9980 and Moen GX100C disposals, among other models. The model name alone does not determine whether a unit is affected; serial information also matters. Read the entire CPSC model and serial table rather than assuming all units in a family are recalled.

If your disposal is covered, follow the recall route before pursuing an ordinary guard repair. CPSC’s remedy is to stop using the recalled disposal and arrange replacement through the named company. Keep the model and serial information available when you seek service.

Sources for this section: 11

Questions about disposal splash guards

Are garbage disposal splash guards universal?

No universal fit is established by the maker documents here. Quiet Collar excludes Badger, and Waste King separates removable EZ Mount guards from built-in Professional 3-Bolt guards. Identify the disposal model and its current part reference before using a seller’s diameter or brand list.

Can I replace the guard without removing the disposal?

Yes, when the model has a documented removable insert. Evolution Quiet Collar, Waste King EZ Mount and the specified Moen removable guards have that access route. Disconnect electrical power first. A fixed baffle or initial Badger conversion needs its own instructions and may require service.

Which splash guard fits an InSinkErator Badger?

InSinkErator identifies the Baffle Upgrade Kit for Badger disposals. The catalog reference is BUK-00 / 78529-ISE. Confirm the kit instructions for the initial conversion; do not assume a fixed baffle already lifts out. Quiet Collar QCB-AM is expressly excluded for Badger.

Does an Evolution Quiet Collar fit a Badger?

InSinkErator says it does not. QCB-AM / 74653D is the Quiet Collar reference, while BUK-00 / 78529-ISE is the Badger upgrade route. The shared InSinkErator brand does not make these accessories interchangeable.

Why won’t the guard pull out of my Waste King 9980?

Waste King describes Professional 3-Bolt guards as built in, so pulling harder is not the right next step. Confirm your exact model’s mount and service instructions. Also check an older 9980 against CPSC recall 17-129 using its model and serial number before further use.

Does Waste King EZ Mount use 1025 or 1027?

The maker references conflict. The Waste King FAQ calls 1025 a splash guard and stopper; the L-2600 drawing calls 1025 a stopper alone and 1027 a stopper and removable-guard pack. Ask Waste King to confirm your model and package contents before ordering.

Which Moen models use splash guard 205497?

Moen’s EXP11982PT sheet names GXP33c and GXP50c, and EX50CPT names EX50c and EX75c. Both identify removable guard 205497. For EX100C, I use its separately linked EXP12254CPT drawing, which expressly names EX100C and the same guard. The drawings do not establish that 1016 and 205497 are interchangeable.

Can my removable guard go in the dishwasher?

Moen permits dishwasher cleaning of its removable guard, and Waste King permits it for EZ Mount. Confirm the cleaning instructions for your actual model before applying that advice. Disconnect the disposal’s power before removing the guard and keep hands outside the chamber.

Why does the sink drain slowly with the guard installed?

Check the model fit and seating, then investigate the drain if slow flow remains. Moen identifies slow drainage and guard buildup as separate potential odor sources. The evidence here does not establish that replacing a baffle cures a blocked drain. Do not cut the guard’s slits as a repair.

Is the rubber splash guard also the seal for an under-sink leak?

Do not assume that. Moen’s parts list separates the removable guard, sink flange and fiber gasket. Locate the actual leak with electrical power isolated. If the mount or plumbing needs disconnection, use the model’s repair procedure or have a licensed plumber handle it.

How often should I replace a disposal splash guard?

No universal replacement interval is established in the maker evidence here. Inspect an identified removable guard with electrical power disconnected, and clean it by the maker’s method if it remains intact. Replace a torn or missing guard with the matching reference rather than following an invented calendar.

Can I use the disposal with the splash guard removed?

Reinstall the correct guard before restoring normal operation. InSinkErator describes upward splash control and noise muffling as baffle purposes, and Moen’s cleaning sequence reinstalls the guard before power returns. Keep power isolated during inspection or replacement; do not reach into the open chamber.

How I choose replacement parts

Why I choose by model

I match the replacement route to the exact disposal model. I check fit and safety against maker documents and CPSC, and keep unresolved part references visible.

How I pick

I read the InSinkErator accessory descriptions, Waste King FAQ and Moen model drawings. I match the OEM reference before selecting an Amazon offer. Each part fits a different disposal family, so the model decides, not a score, and no measured noise result is claimed.

I checked the three original branded offers on Nov 18, 2026, 1:30 AM EST. All three had a New, in-stock offer. QCB-AM is sold by AM Incorporated; the Badger kit and Waste King 1025 are sold by Amazon.com. Seller and condition may change.

Scroll across the table to see every column.

CheckAcceptance ruleWhat stops a recommendation
Exact model fitMaker names the model or documented accessoryOnly a diameter or broad brand claim
Access instructionsModel-specific removal or conversion procedureFixed guard treated as a lift-out insert
Amazon offerGenuine branded model, New and in stockReplacement-for branding or scarce unresolved pack
Conflicting referencesMaker evidence controls; model checkedPackage contents or supersession remains unresolved
ScoringNone; each part fits a different disposal familyUnsupported performance comparison

Sources

  1. InSinkErator Quiet Collar Sink Baffle (Evolution Series), SKU 74653D; Baffle Upgrade Kit, SKU 78529-ISE; Removable Sound Baffle, SKU 08302D. Product descriptions and features, insinkerator.com, checked October 20, 2026. Source
  2. InSinkErator P511-26A, document 138296, effective October 12, 2026, p. 4, accessory model/part table. insinkerator.com/documents/p511-26a-83-10-en-138296.pdf. Source
  3. InSinkErator Installing a Replacement Garbage Disposal, steps 12–13: Quiet Collar seating and leak check before power. insinkerator.com/en-us/support/installing-a-replacement-garbage-disposal. Source
  4. InSinkErator Badger Series installation, care and use manual 138440, 81168 Rev B: leak test and safety notices. Saved maker document reviewed October 20, 2026.
  5. Waste King FAQs: model label, mount differences, cleaning, drain widths and sink-hole answer. wasteking.com/support/faq, checked October 20 and re-read Oct 22, 2026 (EZ Mount guard: item 1025 on Amazon). Source
  6. Waste King and Moen 1025 package references: the current Waste King FAQ and Moen odor article describe a guard and stopper; L-2600PT identifies 1025 as stopper only and 1027 as the guard/stopper pack. Checked November 15, 2026. Source
  7. Waste King Illustrated Parts for L-2600, L-2600PT, Rev. 9/21, p. 1: 1025 versus 1027 contents. assets.moen.com/shared/docs/exploded-parts-views/l-2600pt.pdf. Source
  8. Moen Illustrated Parts EXP11982PT, Rev. 03/23, GXP33c/GXP50c; EX50CPT, Rev. 11/21, EX50c/EX75c; p. 1 of each. assets.moen.com/shared/docs/exploded-parts-views/. Source Current EX100C page also links EXP12254CPT, which names EX50C and EX100C with guard 205497, checked November 15, 2026. EX100C drawing
  9. Moen Garbage Disposal Instruction Sheet INS10477C, 6/22, pp. 2–4: separate parts, electrical safety and falling-unit warning. assets.moen.com/shared/docs/instruction-sheets/ins10477c.pdf. Source
  10. Moen How do I Eliminate Odors in a Garbage Disposal: power isolation, removable-guard cleaning and reinstallation. solutions.moen.com, checked October 20, 2026. Use EXP12254CPT for EX100C; the older EX50c/EX75c sheet alone does not establish that model’s fit. Source
  11. CPSC Anaheim and Moen Recall Garbage Disposals Due to Impact Hazard, April 11, 2017, recall 17-129: model/serial table and stop-use remedy. A recall title search for Waste King on saferproducts.gov, Oct 22, 2026, found no other. cpsc.gov/Recalls/2017/Anaheim-and-Moen-Recall-Garbage-Disposals. Source
  12. Amazon product and New-offer details checked Nov 18, 2026, 1:30 AM EST: QCB-AM (AM Incorporated), Badger kit and Waste King 1025 (Amazon.com). All three in stock. Product photos from the corresponding Amazon listings. Seller and condition may change.
  13. Reader questions: r/Plumbing threads reviewed October 20 cover about Waste King 9980 guard replacement and restricted flow. Reader questions guide the FAQ; they do not establish product fit.