Plumbing PicksCompare the machines

RIDGID K-400 vs K-45

For RIDGID K-400 vs K-45, I choose the K-45AF for fixture drains and the K-400 for larger branch lines, with the right cable. [1] [2] [3]

Updated November 15, 2026. Models, manuals and new Amazon offers checked.

In my 7 years of experience, these are the products I'd install.

As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

RIDGID bundle showing the K-400 and K-45AF drain cleaning machines
K-400 and K-45AF bundle. Photo from the Amazon listing.

Short answer

I’d buy the K-45AF for sinks, tubs and other small fixture drains, and the K-400 for larger branch lines with the proper cable. Neither is my choice for roots. [1] [2] [3]

K-45AF for fixture drains · K-400 for larger branch lines [1] [2] [3]

Check your drain size

Picks by need

Buy the RIDGID K-45 if you mostly clear sinks, lavs, tubs and showers. It is a hand-held machine for 3/4 to 2-1/2 inch lines that weighs 12.6 to 13.8 lb with cable, per RIDGID. Buy the RIDGID K-400 if you clear 1-1/2 to 4 inch lines like laundry, floor drains and branch lines. RIDGID says the K-400 is not designed to remove roots. The two overlap only from 1-1/2 to 2-1/2 inch (my arithmetic), so a busy shop may want both. [1] [2] [3]

For most fixture clogs: the RIDGID K-45AF, a hand-held AUTOFEED sink machine for 3/4 to 2-1/2 inch lines. Check the RIDGID K-45AF on Amazon [1] [2] [3]

The RIDGID K-400 and K-45 do not compete for the same drain. The K-45 is a hand-held sink machine for 3/4 to 2-1/2 inch lines: lavs, kitchen sinks, tubs, showers and urinals. The K-400 is a drum machine on a cart for 1-1/2 to 4 inch lines. They overlap only from 1-1/2 to 2-1/2 inch (my arithmetic), so the question is which lines you clear most. [1] [2] [3]

If you are pricing the RIDGID K400 as your first machine, this page shows where it stops and where the K-45 takes over. For every machine type together, see the best drain cleaning machines. I run RIDGID and Milwaukee tools on my own jobs; every spec below comes from RIDGID’s manuals and catalog. [1] [2] [3]

Find the machine for your drain

I start with the line size and the obstruction. This check cannot replace a drain inspection or the machine’s manual.

Choose both answers to compare the machine ranges.

K-400 vs K-45 Side by Side

Machine-family specifications. Cable and kit contents matter: use RIDGID’s manual for the exact cable. Swipe the table sideways on a phone.
SpecificationK-45 / K-45AF (sink machine)K-400 (drum machine)
DesignHand-held, variable speed switch and FOR/REV switchWheeled drum machine, foot switch and FOR/OFF/REV switch
Line size3/4 to 2-1/2 in. (manual and US catalog) [1] [2] [3]1-1/2 to 4 in. [1] [2] [3]
Cable diameters1/4, 5/16, 5/16 inner core, 3/8 in. [1] [2] [3]3/8 and 1/2 in. integral wound [1] [2] [3]
Cable in the drumUp to 50 ft, depending on cable [1] [2] [3]100 ft of 3/8 in. or 75 ft of 1/2 in. [1] [2] [3]
Max line length30 to 45 ft, depending on cable [1] [2] [3]Up to 100 ft, depending on cable [1] [2] [3]
Speed0 to 650 RPM (manual); 0 to 600 RPM (US catalog) [1] [2] [3]170 RPM (120V) [1] [2] [3]
Motor250 to 280 W universal (manual) [1] [2] [3]1/3 HP induction, belt drive [1] [2] [3]
AUTOFEEDK-45AF models [1] [2] [3]Add-on or AF kits; 12 to 15 ft per min [1] [2] [3]
Weight12.6 lb manual feed, 13.8 lb AUTOFEED, with C-1IC cable (manual) [1] [2] [3]40 lb machine only; 66 lb with 3/8 x 75 ft cable (manual); US catalog lists kit 52363 at 68 lb [1] [2] [3]
ElectricalDouble insulated, polarized plug; GFCI on 120V units if equipped [1] [2] [3]Grounded; GFCI built into the cord
Keep cable outlet within6 in. of the drain (setup steps); 12 in. (safety rules, manual-feed steps) [1] [2] [3]2 ft of the drain [1] [2] [3]
Machine fit, per RIDGIDSecondary drain lines up to 2-1/2 in. (manual) [1] [2] [3]Not designed to remove root blockages
Linked kit35473 K-45AF, 5/16 x 25 ft C-1IC [1] [2] [3]52363, 3/8 x 75 ft C-32 IW [1] [2] [3]

From RIDGID’s K-400 and K-45 operator’s manuals and US full-line catalog, checked November 15, 2026. Where RIDGID documents give different numbers, each is shown. I rechecked the linked new offers on November 15, 2026; seller and stock can change.

Which One Should You Buy?

Start with the line size you clear most

Plumber’s note: most sink, lav and tub clogs sit in 1-1/4 to 2 inch pipe close to the fixture (my judgment, not a RIDGID figure). That is K-45 work. Laundry standpipes, floor drains and 3 inch branch lines are K-400 work, and so is 4 inch with the 1/2 inch cable. RIDGID’s manuals both say to use the drain cleaner only for the recommended drain sizes, because the wrong size can twist, kink or break the cable. [1] [2] [3]

Plumber’s note: a 3/8 inch cable driven into a 4 inch line has room to loop and knot; RIDGID’s K-400 manual warns that feeding cable into a larger drain can make it kink or knot. Match the cable to the pipe. [1] [2] [3]

Hand-held or on the floor

The K-45 goes where the drain is. You hold it, aim the cable outlet within 6 inches of the drain and work the variable speed switch. The K-400 sits on the floor within 2 feet of the opening. You feed the cable with gloved hands and run the motor with a foot switch. Both manuals say one person must control both the cable and the switch. On the K-400 that frees both hands for the cable, which matters on a long run. [1] [2] [3]

Weight and getting to the job

RIDGID lists the K-45 at 12.6 to 13.8 lb with C-1IC cable in its manual. The K-400 manual gives 40 lb for the machine alone and 66 lb with 3/8 by 75 foot cable; the US catalog lists kit 52363 at 68 lb. The catalog’s 60 lb figure belongs to the shorter 50 ft kit, not this 75 ft kit. That is roughly three to five times the weight (my arithmetic). The K-400 rolls on its cart, and RIDGID says the wheels handle stairs; the K-45 carries in one hand. [1] [2] [3]

AUTOFEED

Both machines come in manual feed and AUTOFEED versions. On the K-45AF, a lever advances or retrieves the rotating cable. On the K-400, AUTOFEED is a bolt-on assembly (catalog number 26773) with a handle that advances or retrieves at 12 to 15 feet per minute, per the manual. Either machine with AUTOFEED can still be fed by hand. The linked K-45AF has AUTOFEED; the linked K-400 kit is manual feed. [1] [2] [3]

Best for Sinks, Lavs, Tubs and Showers

RIDGID K-45AF Sink Machine (35473)

Buy it if I need a hand-held machine for small fixture lines. Skip it if the job needs 3 or 4 inch cable capacity. The tradeoff is carrying the weight in my hands rather than rolling a cart. [1] [2] [3]

RIDGID K-45AF Sink Machine (35473)

$470.98 at Amazon

Price as of 2026-11-15 22:15 UTC. Sold by U.S. Products & Designs. Only 2 left in stock - order soon.

Check price on Amazon

Product photo from the Amazon listing.

Hand-held sink machine · 3/4 to 2-1/2 in. lines (manual) · 1/4, 5/16 and 3/8 in. cables, up to 50 ft in the drum · variable speed 0 to 650 RPM (manual) · AUTOFEED · 12.6 lb manual feed, 13.8 lb AUTOFEED with C-1IC cable · double insulated, GFCI on 120V units if equipped [1] [2] [3]

RIDGID’s manual calls the K-45 a hand-held machine for secondary drain lines, the kind found in kitchens, bathrooms and utility rooms, from 3/4 to 2-1/2 inch with the correct cable. The drum holds up to 50 feet of cable, depending on the cable. You hold it by a hand grip, run it with a variable speed ON/OFF switch and a FOR/REV switch, and lock the cable with a slide-action chuck. [1] [2] [3]

RIDGID’s US catalog lists 3/4 to 2-1/2 inch lines and 0 to 600 RPM; the manual lists 0 to 650 RPM and 250 to 280 W. I use the manual for operating limits and keep the speed difference visible. [1] [2] [3]

The linked machine is catalog number 35473, the K-45AF, which RIDGID’s catalog lists with AUTOFEED and a C-1IC cable: 5/16 inch by 25 feet, inner core, with an inner drum. The manual rates 5/16 inch inner core cable for 1-1/4 to 2 inch lines up to 45 feet long. The Amazon listing says this cable suits 3/4 to 1-1/2 inch lines, which matches the manual’s rating for plain 5/16 inch cable, not the inner core version. [1] [2] [3]

RIDGID’s US catalog gives 3/4 to 1-1/2 inch lines for 5/16 inch cable and 1-1/4 to 2-1/2 inch lines for 3/8 inch cable. The manual separately identifies the inner-core cable ratings. If you would rather feed by hand, the manual-feed K-45 (36018) comes with the same C-1IC cable. [1] [2] [3]

  • Weighs 12.6 to 13.8 lb with cable, per the manual, so you carry it to the fixture
  • AUTOFEED advances and retrieves cable with a lever; the manual says it helps keep hands and the work area clean
  • Variable speed switch plus FOR/REV in one hand-held unit
  • Inner drum for quick cable changes; RIDGID says it helps prevent cable flip-over and drum leaks
  • Tops out at 2-1/2 in. per the manual and US catalog; not for 3 and 4 in. lines or mains
  • Line length limits of 30 to 45 ft, depending on the cable, per the manual
  • The cable is not attached to the inner drum, so the last 5 to 7 ft need care
  • Hand-held, so your arm and grip carry the load on a tough clog

Verdict: The machine for sinks, lavs, tubs, showers and urinals: small lines where a 60 lb drum machine is too much. [1] [2] [3]

Check the RIDGID K-45AF sink machine (35473) on Amazon
Best for 1-1/2 to 4 Inch Lines

RIDGID K-400 Drum Machine (Kit 52363)

Buy it if I need a foot-switch machine for branch lines. Skip this 3/8 inch kit when the job calls for 1/2 inch cable. The tradeoff is a heavier machine and more setup space. [1] [2] [3]

RIDGID K-400 Drum Machine (Kit 52363)

$629.00 at Amazon

Price as of 2026-11-15 22:15 UTC. Sold by Amazon.com. Only 3 left in stock (more on the way).

Check price on Amazon

Product photo from the Amazon listing.

Drum machine on a wheeled cart · 1-1/2 to 4 in. lines · 3/8 in. cable for 1-1/2 to 3 in., 1/2 in. cable for 3 to 4 in. (manual) · drum holds 100 ft of 3/8 in. or 75 ft of 1/2 in. · 1/3 HP · 170 RPM · foot switch · built-in GFCI · 40 lb machine only, 66 lb with 3/8 x 75 ft cable (manual) [1] [2] [3]

The K-400 is a drum machine. The cable lives in a corrosion-resistant drum spun by a belt-driven 1/3 HP motor at 170 RPM, per the manual. RIDGID rates it for 1-1/2 to 4 inch lines up to 100 feet, depending on the cable. The manual pairs 3/8 inch cable with 1-1/2 to 3 inch lines and 1/2 inch cable with 3 to 4 inch lines. [1] [2] [3]

RIDGID’s US catalog also pairs 1/2 inch cable with 3 to 4 inch lines. I follow the manual’s cable chart for the operating range. You run it with a FOR/OFF/REV switch and a pneumatic foot switch, and a GFCI is built into the cord. [1] [2] [3]

RIDGID’s Cable Control System is a torque limiter that stops the drum when the cable end stops turning and torque passes a set value, to help prevent cable flip-over in the drum. The manual says it is designed for RIDGID 3/8 and 1/2 inch integral wound (IW) cable and may not protect other cables. The linked kit (52363) comes with a C-32 IW cable, 3/8 inch by 75 feet, the T-260 tool set (bulb auger, “C” cutter, spade cutter and pin key) and gloves, per RIDGID’s catalog. [1] [2] [3]

For 3 to 4 inch lines, the K-400 kit 26998 has a 1/2 inch by 75 foot C-45 IW cable. AUTOFEED is an add-on (catalog number 26773), and the manual gives its feed rate as 12 to 15 feet per minute. [1] [2] [3]

  • Covers 1-1/2 to 4 in. lines with two cable sizes
  • Foot switch leaves both gloved hands on the cable
  • Built-in GFCI in the cord, plus a torque limiter for RIDGID IW cable
  • Cart with a fold-over handle and wheels; RIDGID says it handles uneven ground and stairs
  • RIDGID’s manual says it is not designed to remove root blockages
  • 40 lb for the machine alone and 66 lb with 3/8 x 75 ft cable, per the manual (US catalog: 68 lb for kit 52363)
  • Must sit within 2 ft of the drain, or the access must be extended, per the manual
  • Overkill for a lav or a kitchen sink trap arm

Verdict: The machine for tub, laundry, floor drain and 3 to 4 inch branch lines, with the correct cable and without root blockages. [1] [2] [3]

Check the RIDGID K-400 kit (52363) on Amazon

Other feed and cable configurations

I keep the manual-feed option, larger-cable kit and two-machine bundle separate so the cable in the box stays clear.

K-45 manual feed 36018

RIDGID K-45 manual feed 36018

Photo from the Amazon listing.

For hand feeding. C-1IC 5/16 in. × 25 ft inner-core cable; skip it if you want the K-45AF feed levers. [1] [2] [3]

$488.28 at Amazon

Price as of 2026-11-15 22:18 UTC. New, sold by Amazon.com. Only 2 left in stock (more on the way).

Check price on Amazon

K-400 kit 26998

RIDGID K-400 kit 26998

Photo from the Amazon listing.

For the 1/2 in. × 75 ft C-45 IW cable. Use the manual’s 3 to 4 in. line range; this remains unsuitable for roots. [1] [2] [3]

$770.39 at Amazon

Price as of 2026-11-15 22:18 UTC. New, sold by Amazon.com. Only 1 left in stock - order soon.

Check price on Amazon

K-400 and K-45AF bundle

See the exact bundle photo at the top.

For a shop covering both kinds of drain. Read the bundle contents before buying; its AUTOFEED K-400 differs from the manual-feed 52363 kit above. [1] [2] [3]

$1,486.72 at Amazon

Price as of 2026-11-15 22:18 UTC. New, sold by Amazon.com. Only 14 left in stock - order soon.

Check price on Amazon

Before You Buy

  1. List the lines you clear.

    3/4 to 2 inch fixture lines point to the K-45. 3 and 4 inch lines need the K-400.
  2. Pick the cable with the machine.

    On the K-45, 1/4 and 5/16 inch cable is for 3/4 to 1-1/2 inch lines, 5/16 inch inner core for 1-1/4 to 2 inch and 3/8 inch for 1-1/4 to 2-1/2 inch, per the manual. On the K-400, 3/8 inch is for 1-1/2 to 3 inch and 1/2 inch for 3 to 4 inch. When a cable wears out, RIDGID lists the replacement by catalog number for each machine and line size; see RIDGID K-45 and K-400 replacement cables.
  3. Check the outlet.

    The K-400 has a GFCI in its cord. The K-45 manual lists a GFCI on 120V units “if equipped.” Both manuals say the cord GFCI does not protect an extension cord, so use a GFCI-protected outlet or a plug-in GFCI.
  4. Know what roots need.

    Neither machine is designed for root removal. RIDGID says the K-400 is not designed for roots.
  5. Plan to look.

    Both manuals say the best way to judge a drain’s condition before cleaning is a camera inspection. See the best sewer inspection cameras.

Running Either Machine Safely

I call a qualified drain specialist when I suspect roots, a collapsed line, repeated backups or an unknown drain route. I stop a machine that binds instead of forcing more cable into the line.

The two manuals share most of their rules. Wear safety glasses and RIDGID drain cleaning gloves, with latex or rubber gloves underneath when chemicals or bacteria may be in the line. Test the GFCI before each use, and do not run either machine while you or it stand in water. Feed at least a foot of cable into the drain before you start, so the end cannot whip.

Do not let the cutter stop turning while the cable is turning; pull the cable back from the obstruction, then feed it back slowly and let the spinning end dwell in the blockage. Run REV only for a few seconds to free a stuck tool or start through a trap, and never retrieve in REV.

Both manuals also say to pull a fixture such as a toilet or urinal rather than feed the cable through it.

For tool size, both manuals give the same rule of thumb: start with the smallest tool to get water moving, and keep the largest tool no bigger than the inside diameter of the pipe minus one inch. The K-400 kit ships with a bulb auger for exploring and pulling hair, a “C” cutter for grease and a spade cutter for floor drains, per the manual. [1] [2] [3]

Most K-45 cables end in a bulb auger; its C-4, C-6 and C-6IC cables have a male coupling for other heads. Plumber’s note: when the line is flowing, run water while you retrieve the cable. Both manuals call for it, and it rinses the cable on the way back in. [1] [2] [3]

FAQ

Can the K-45 clean a 3 or 4 inch line?

No. RIDGID’s K-45 manual lists 3/4 to 2-1/2 inch lines, and its 3/8 inch cable is rated for 1-1/4 to 2-1/2 inch lines up to 30 feet. RIDGID’s US catalog also limits the K-45 to 2-1/2 inch lines. For 3 to 4 inch lines, RIDGID pairs the K-400 with 1/2 inch cable. [1] [2] [3]

Can the K-400 clear roots in a sewer line?

No. RIDGID’s K-400 manual says the K-400 is not designed to remove root blockages. RIDGID’s catalog lists larger drum machines, such as the K-750 and K-7500, for 3 to 8 and 3 to 10 inch lines. My cable machine vs jetter guide covers the step up. [1] [2] [3]

Can I run either machine in reverse?

Only as the manuals describe. Both manuals say not to run the cable in REV except to back a tool out of a blockage or get it started through a trap, and only for a few seconds. Both say running in reverse can damage the cable. Never retrieve the cable in REV.

What gloves should I wear?

RIDGID drain cleaning gloves. Both manuals say never to grasp the rotating cable with anything else, including a glove or a rag, because it can wrap around the cable. Latex or rubber gloves can go under the RIDGID gloves for chemicals and bacteria. Every K-400 and K-45 comes with one pair of RIDGID drain cleaning gloves, per the manuals. [1] [2] [3]

Is there a bundle with both machines?

Yes. Amazon lists a RIDGID bundle with the K-400 and the K-45AF. Per the listing, it includes a K-400 with AUTOFEED and 75 feet of solid core cable, a K-45AF with 25 feet of inner core cable, gloves and manuals for both. [1] [2] [3]

Where the documents and listings differ

The K-45AF Amazon listing gives 0 to 600 RPM and about 11 lb; RIDGID’s manual gives 0 to 650 RPM and 13.8 lb with C-1IC cable. The bundle listing gives 165 RPM for its K-400, while the current K-400 manual gives 170 RPM. I use the manual for setup and safe operating limits, and confirm the nameplate and included cable before ordering a specific kit. [1] [2] [3] [4]

Why Trust Plumbing Picks

How we chose

I compared two machine families, RIDGID K-45 and K-400, in five linked configurations using RIDGID’s operator manuals, US full-line catalog and the exact Amazon listings. I choose the cable range first, then access, handling weight and feed controls.

I compare the exact cable in each kit with RIDGID’s operating range, then check access, feed controls and handling weight. All five existing linked configurations remain available as new Amazon offers; none was replaced. My drain-size check uses the manual’s cable ranges, with no price-based ranking.

I write Plumbing Picks as a licensed Georgia journeyman plumber and use RIDGID and Milwaukee tools on jobs. Every spec here comes only from the RIDGID documents listed below or from the Amazon listings I link. I checked the exact linked models and new offers on November 15, 2026; stock and sellers can change. If you buy through a link I may earn a commission at no extra cost to you. Nobody pays to be included here. More on who writes this and how we pick.

Sources

Bottom Line

The K-45 and K-400 split by pipe size. The K-45 is the hand-held machine for 3/4 to 2-1/2 inch fixture lines, with AUTOFEED on the AF models. The K-400 is the floor machine for 1-1/2 to 4 inch lines, with a foot switch, a built-in GFCI and a torque limiter for RIDGID IW cable. Neither is designed for root removal. Pick by the lines you clear most, and match the cable to the pipe. [1] [2] [3]

Related Plumbing Guides