Most kitchen sprayer problems are a ten-minute part swap. On a side sprayer with a sound hose, replace the head with the Danco 88760; if the hose leaks too, the universal head-and-hose set covers it, and the Moen 136103SL is the factory part. On a pull-down faucet the Hibbent 3-function head fits most brands.
Plumbing Picks is reader-supported. As an Amazon Associate, we earn from qualifying purchases at no extra cost to you.
A kitchen sprayer that leaks, won’t switch from spray to stream, or has gone weak is one of the most annoying small problems in a kitchen — and one of the cheapest to fix. The head and the hose are replaceable independently of the faucet, and on most sinks it’s a ten-minute job with no tools. Here’s what fits what.
Changing the whole faucet? Check the hole count first.
| Replacement part | Best for | Price tier |
|---|---|---|
| Danco 88760 Universal Fit Sink Spray Head | Head-only swap on a side sprayer, any brand | Budget |
| Universal side sprayer with hose and holder | Whole side-spray assembly on a budget | Budget |
| Moen 136103SL side spray head and hose | Genuine Moen part with quick-connect hose | Mid |
| Hibbent 3-function pull-down spray head | Pull-down and pull-out faucets, most brands | Budget |
| Delta RP44647 hose assembly | Genuine Delta OEM pull-out part | Premium |
Prices change constantly — check the current price on Amazon before you buy.
Quick picks: Head-only side sprayer: Danco 88760 · Genuine Moen part: Moen 136103SL · Pull-down spray head: Hibbent 3-function. Full reasoning below.
First: which kind of sprayer do you actually have?
Nearly every wrong part I see ordered comes down to this one confusion, so settle it before you buy anything.
- Side sprayer — a separate wand sitting in its own hole in the deck or sink, beside the faucet. Its hose runs down and connects to a diverter on the faucet body under the sink.
- Pull-down or pull-out — the spout is the sprayer. You pull the head out of the spout and a weighted hose retracts it.
The two share nothing. A side-spray head will not fit a pull-down spout, and the reverse is just as true.
Then: head only, or head and hose? Unscrew the head from the hose, turn the water on, and watch the bare hose end. Water only at the end means the head is the problem — buy the head. A drip anywhere along the hose, or at the connection under the sink, means the assembly goes.
Best Head-Only Side Sprayer
Danco 88760 Universal Fit Sink Spray Head
If your hose is sound and only the head has failed, this is the part. Danco sells it as universal fit, it threads onto the standard side-spray hose, and it costs about a fifth of the branded assembly. It is one of the most widely bought parts of its kind, which is a lot of real-world data for a part this cheap.
- ✅ Cheapest honest fix when the hose is fine
- ✅ Universal thread — no brand matching
- ⚠️ It’s a budget part, and it reads like one in the hand
Check the Danco 88760 price on Amazon →
Best Budget Side-Spray Assembly
Universal Side Sprayer With Hose and Holder
When the hose is the problem, replacing head and hose together costs barely more than a good head on its own. This universal set includes the sprayer, the braided hose and the deck holder, uses a quick side connector, and is the option I’d reach for on any faucet that isn’t worth an OEM part.
- ✅ Everything in one box — head, hose, holder
- ✅ Around a third the price of the Moen assembly
- ⚠️ Check your existing connection type at the faucet body before ordering
Best Genuine Moen Part
Moen 136103SL Side Spray Head and Hose
If you have a Moen faucet with the quick-connect side-spray hose, the connection Moen has fitted since 2007, and you want the factory part, this is it: stainless head plus hose. Check the hose end under your sink before you order. On the older threaded connections Moen used before then, this is still the spray they point you to, but an adapter kit has to go with it, and Moen are explicit that the adapter is not an optional part. Be clear-eyed about the trade — it costs roughly three times the universal set, and it is not better made. Buy it because you want an exact Moen fit and finish, not because it’s the more reliable part.
- ✅ Exact Moen fit, quick-connect, stainless finish
- ⚠️ Three to four times the price of a universal assembly that does the same job
Check the Moen 136103SL price on Amazon →
Best Pull-Down / Pull-Out Spray Head
Hibbent 3-Function Pull-Down Spray Head
Pull-down heads aren’t standardised the way side-spray threads are, which is exactly why the good universal ones ship with a tray of adapters. The Hibbent head is NSF/ANSI 61 and cUPC certified — worth something on a part that sits in your drinking water — has three spray modes.
- ✅ NSF/ANSI 61 and cUPC certified
- ✅ Three functions: stream, spray, high-pressure rinse
- ✅ Fits most major brands via the included adapters
Check the Hibbent 3-function price on Amazon →
Cheaper alternative: the J-HVA pull-down head is the budget version of the same idea — three functions, the same 15-adapter tray, and its listing states the same NSF/ANSI 61 certification (the Hibbent also carries cUPC). Its own listing asks you to confirm your connection size before ordering, so fit is the bet you are taking. See it on Amazon →
Best Genuine Delta Part
Delta RP44647 Hose Assembly
Delta’s own RP44647 hose assembly is the factory replacement for the Waterfall pull-out kitchen faucets (474/476), and it is the right answer if you want the finish and the fit to match exactly. It is also the priciest option here — several times a universal head. My honest advice: on a mid-range faucet, fit the universal head. On a high-end Delta you plan to keep for another decade, buy the OEM part and be done.
Watch out: search results for “RP44647” are full of cheap aftermarket hoses that are compatible with the Delta part, not the Delta part. If the listing doesn’t say Delta Faucet, it isn’t.
Check the Delta RP44647 price on Amazon →
How to replace a kitchen side sprayer
- Turn off both supply valves under the sink.
- Disconnect the sprayer hose from the faucet body — usually a push-connect or a threaded fitting on the diverter.
- Thread the new hose up through the sprayer hole in the deck.
- Connect it to the faucet body: hand-tight for threaded, a firm push until it clicks for quick-connect.
- Turn the water back on and run every spray mode, checking under the sink for leaks.
How to replace a pull-down spray head
- Pull the head out of the spout as far as the hose allows.
- Unclip or unscrew the weight from the hose so you can work freely.
- Unscrew the old head from the hose end — counter-clockwise, by hand. Years of scale can make it stiff; a rubber jar-opener beats a wrench, which will mar the finish.
- Match the old connector against the adapters in the kit, fit the right one, and hand-tighten the new head.
- Refit the weight, run the water, and check the connection at full pressure before you push the head back into the spout.
Tip: if the sprayer has slowly lost pressure rather than failing outright, pull the screen inside the head before buying anything. Mineral buildup restricts flow, and an overnight soak in white vinegar clears it. That fix is free.
If the sprayer is built into the spout rather than sitting in its own hole, the choice is pull-down vs pull-out — different spout heights, different sinks, and a docking mechanism that decides whether the head sags in two years.
If the sprayer isn’t the real problem
A sprayer that keeps failing on an aging faucet is often the faucet talking. Two honest paths: replace the cartridge first if the body is sound — see the faucet cartridge guide — or replace the faucet and get a fresh sprayer with it:
- Moen Arbor pull-down kitchen faucet — a workhorse pull-down with the sprayer built into the head.
What Is the Best Replacement Kitchen Sprayer?
There is no single answer — it depends on what you have. For a side sprayer with a good hose, the Danco 88760 head is the sensible fix. If the hose has gone too, the universal head-and-hose set does the whole job. On a pull-down faucet, the certified Hibbent 3-function head fits most brands through its adapter tray.
Will Any Side Sprayer Fit My Faucet?
On a side sprayer, almost always — the hose thread is effectively standard, which is why Danco sells the 88760 as universal fit. The exceptions are branded quick-connect hoses: Moen has fitted a quick-connect side-spray connection since 2007, and its older threaded connections need Moen’s adapter kit. Check the hose end under the sink before ordering.
Side Sprayer vs Pull-Down Faucet: Which Should You Replace?
They are different repairs. A side sprayer sits in its own hole and connects to a diverter under the faucet, so head and hose are replaceable on their own. On a pull-down, the spout is the sprayer — you replace the head, or the whole faucet. The two share nothing, so identify yours before you order.
FAQ
How do I know if my sprayer is repairable or needs full replacement?
If the head leaks or doesn’t switch modes, replace the head only. If the hose is kinked, cracked, or leaks at the faucet connection, replace the full assembly. Head-only replacement is the cheaper route; a full assembly costs more but takes the guesswork out of fit.
Can I use a universal head on a brand-name faucet?
On a side sprayer, almost always — the hose thread is effectively standard. On a pull-down, it depends on the connector, which is why the universal kits include adapters. Keep the old head until the new one is installed and holding, so you have something to match against.
Why does my sprayer work but the faucet loses pressure when I use it?
That’s the diverter inside the faucet body, not the sprayer. Some drop in pressure is normal by design. A big drop, or water coming out of both at once, means the diverter is worn — a separate and slightly deeper repair.
Does a new sprayer head fix low water pressure?
Only if the head is the restriction. Clean the screen first. If pressure is low at every fixture in the house, the sprayer is not your problem.
Bottom Line
Diagnose before you buy: side sprayer or pull-down, head or whole assembly. For a side sprayer with a good hose, the Danco 88760 is the sensible fix. If the hose has gone too, the universal head-and-hose set beats paying up for the Moen assembly unless you specifically want the factory part. For pull-down faucets, the certified Hibbent head handles most brands — and the genuine Delta RP44647 is worth its price only on a faucet you intend to keep for years.
If the sprayer hose is cracking, the diverter is usually not far behind, and on many faucets the diverter is a replaceable part — here’s how to clean or replace a kitchen faucet diverter, with the exact Delta, Moen, and Kohler parts. If the faucet itself is worn, pricing a whole faucet can still make more sense than chasing the third component.
Fix the 12 Most Common Plumbing Problems Yourself — Free Plumber’s Handbook — including the 10-minute faucet fixes anyone can do
Step-by-step fixes for the 12 most common problems — and exactly when to call a pro. Free and instant, from a licensed plumber. Save hundreds on calls you didn’t need.