Press fitting starter kit: what to stock

Press fitting starter kit: what to stock for fixed-pipe repairs, new runs and threaded connections.

As an Amazon Associate I earn from qualifying purchases. How this site earns

Viega 78172 half-inch ProPress coupling without stop
Viega 78172 coupling without stop. Product photo from Amazon.

The short answer

Start with Viega ProPress ½ and ¾ inch couplings, with and without a stop, plus elbows, tees and bronze threaded adapters. If my shop runs NIBCO Press, I keep stock within that system and check its tool and jaw chart. [1]

Repairs between fixed pipes
Viega 78172 coupling without stop. It slides fully onto one pipe, then back across the gap.
New runs and loose tube
Viega 78047 coupling with stop. The stop inside sets the insertion depth, so you only have to push the tube home and press.
Turns and branches
Viega 77317 90° elbow, and the 77377 tee. A tee lets you add a branch to an existing line.
Threaded valves and heaters
Viega 79215 press x male NPT adapter. Press on one end, pipe thread on the other.
Top repair fitting: Viega 78172 (½ in.)
$44.71 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

On this page
  1. The core fittings
  2. Why no-stop couplings
  3. No-stop couplings
  4. Stop couplings
  5. Elbows and tees
  6. Threaded adapters
  7. Starter list
  8. Coupling sizes
  9. What they’re made of
  10. What to add next
  11. Bins by job
  12. Bins and restock
  13. Prep and depth
  14. Stocking rules
  15. FAQ
  16. How I pick

Stock finder: which bins does the job pull?

Tell it the press system you stock and the job in front of you. It reads from the same starter list this page stocks: the bins each common job pulls from, below.

1Which press system do you stock?
2What job is in front of you?

Start with question 1: which press system you stock.

The core fittings to start with

Four fittings cover most repair and service work in ½ and ¾ inch. They do different jobs, so they aren’t scored against each other. [1] [10]

Viega 78172 coupling without stop
Best for repairs between fixed pipes

Viega 78172 ½ in. coupling without stop, 5-pack

$44.71 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Sizes
½ and ¾ in., press x press
Body
Zero Lead copper (Viega)
Rating
300 psi (Viega ProPress)
Length
1.61 in. at ½ in.; 2.01 in. at ¾ in.
Model
Viega 2915.3, coupling without stop
Pack
5-pack

Skip it if: You only build new runs where one pipe is always free to move. Stop couplings are simpler.

See sizes and limits
Viega 78047 coupling with stop
Best for joining loose tube

Viega 78047 ½ in. coupling with stop, 5-pack

$22.94 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Sizes
½ and ¾ in.
Rating
300 psi, 0–250°F
Seal
EPDM
Warranty
50-year limited
Length
1.61 in. at ½ in.
Pack
5-pack

Skip it if: Both pipe ends are locked in place. Use a coupling without a stop.

See sizes and limits
Viega 77317 90 degree elbow
Best for ½ in. turns

Viega 77317 ½ in. 90° elbow, 10-pack

$44.34 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Size
½ in. P x P
Body
Zero Lead copper
Rating
300 psi
Model
Viega 2916, 90° elbow
Pack
10-pack

Skip it if: You only do straight cut-out repairs. Couplings cover those.

See sizes and limits
Viega 79215 bronze male threaded adapter
Best for tying into threaded valves

Viega 79215 ½ in. press x male NPT, pack quantity shown on Amazon

$16.58 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Connection
½ in. press x ½ in. NPT
Body
Zero Lead bronze
Model
Viega 2911ZL, male adapter
Threads
ASME B1.20.1
Pack
Pack quantity shown on Amazon

Skip it if: Everything you touch is copper to copper.

See sizes and limits
FittingKey specsPick it ifSkip it if
Viega 78172 ½ in. coupling without stop, 5-pack½ and ¾ in., press x press, Zero Lead copper (Viega), 300 psi (Viega ProPress) [1]You do service repairs where you cut out a bad section between two fixed pipes.You only build new runs where one pipe is always free to move. Stop couplings are simpler.
Viega 78047 ½ in. coupling with stop, 5-pack½ and ¾ in., 300 psi, 0–250°F, EPDM seal, 50-year limited warranty [1] [6]You’re joining new runs or replacing a section where one side can move.Both pipe ends are locked in place. Use a coupling without a stop.
Viega 77317 ½ in. 90° elbow, 10-pack½ in. P x P, Zero Lead copper, 300 psi [1]You want the turns and branches covered for most bathroom and kitchen work.You only do straight cut-out repairs. Couplings cover those.
Viega 79215 ½ in. press x male NPT, pack quantity shown on Amazon½ in. press x ½ in. NPT, Zero Lead bronze [7]You tie into threaded valves, water heaters or old threaded work.Everything you touch is copper to copper.

Source: [1]. Part numbers and specifications follow the maker’s document.

Why a coupling without a stop earns its spot

A common repair is a cut-out in pipe that can’t move. A standard coupling can’t get across that gap. A stopless one can.

With a stop The center stop hits the pipe end,so it can't slide over the gap.Works only if one pipe can move. Without a stop 1. Slide it all the way onto one pipe.2. Slide it back over the gap until both depth marks just show.3. Press both ends. Grey bars: walls or framing holding the pipe. Dark lines: insertion depth marks. With a stop The center stop hits the pipe end, so itcan't slide over the gap. Without a stop 1. Slide it all the way onto one pipe.2. Slide it back over the gap until both depth marks just show.3. Press both ends. Grey bars: walls holding the pipe. Dark lines: depth marks.
Mark the insertion depth on both pipe ends first; Viega’s install steps call for it on every joint. With no internal stop, the marks are the only thing that tells you the coupling is centered.

Couplings without a stop for repairs

Start with ½ inch in each kind, then add ¾ inch for mains and water heaters. [6]

Viega 78172 coupling without stop
Couplings without a stop. Product photo: Amazon.

A coupling with a stop has a shoulder in the middle, so each pipe can only go in halfway. That’s fine when one pipe can slide back. In a wall or ceiling, it usually can’t.

A coupling without a stop slides all the way onto one side, then back over the gap. Mark the insertion depth on both pipe ends, center the coupling between the marks and press both ends. Viega’s ½ inch insertion depth is ¾ inch. [1]

Keep the brand the same as the rest of your stock. If you stock NIBCO instead, its PC601 is the ½ inch repair coupling, which NIBCO catalogs without a stop. [6]

Where it does well

  • Slides fully onto one pipe, then back across the gap
  • Fixes a cut-out without moving either pipe
  • NIBCO PC601 is a separate-brand repair coupling

What to watch

  • No stop means the depth marks are your only check
  • One pipe needs clean, round tube past the cut for the slide

Viega’s drawings put the ½ inch no-stop coupling (model 2915.3) at 1.61 inches long and the ¾ inch 78177 at 2.01 inches. Because it slides fully onto one pipe first, that pipe needs at least that much clean, round tube past the cut. NIBCO lists PC601 as a wrot-copper repair coupling without a stop. I check its technical data separately rather than carrying Viega ratings across brands. [1] [6]

Viega’s submittal lists the no-stop coupling, model 2915.3, in every size a house job needs: 78172 for ½ inch, 78177 for ¾, 78182 for 1, 78187 for 1¼, 78192 for 1½ and 78197 for 2. The 1 inch is 1.97 inches long, a hair shorter than the ¾ inch, so don’t size the slide room by guesswork. Check the length for the size in your hand. [1]

The no-stop coupling also runs on to 2½, 3 and 4 inch (20728, 20733 and 20738), from 4.33 to 5.79 inches long. Viega’s data sheet says those big fittings carry a 420 stainless steel grip ring and a PBT separator ring, and the installer should make sure the grip ring is in place. A compact tool won’t press them. [1]

Best for
You do service repairs where you cut out a bad section between two fixed pipes.
Skip it if
You only build new runs where one pipe is always free to move. Stop couplings are simpler.
Sizes
½ and ¾ in., press x press
Body
Zero Lead copper (Viega)
Rating
300 psi (Viega ProPress)
Length
1.61 in. at ½ in.; 2.01 in. at ¾ in.
Model
Viega 2915.3, coupling without stop
Pack
5-pack
$44.71 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Couplings with a stop for new runs

Viega 78047 coupling with stop
Couplings with a stop, from Viega ProPress. Product photo: Amazon.

This is the joint you’ll make most on new work. The stop inside sets the insertion depth, so you only have to push the tube home and press.

Viega rates ProPress at 300 psi and 0 to 250°F with a 50-year limited fitting warranty for residential and commercial use, and its Smart Connect feature lets an unpressed fitting show itself during the pressure test. That’s why Viega is the brand I’d stock if I could only stock one. [1]

On Viega’s drawings the ½ inch 78047 is 1.61 inches long and 0.08 pounds, and the ¾ inch 78052 is 2.01 inches and 0.131 pounds. That’s the same body size as the no-stop versions, so both kinds fit the same bin. Viega’s listing says each joint takes four to seven seconds and can be made wet, with no torch, solder or flux. [1] [2]

Where it does well

  • The stop sets the depth for you
  • 300 psi and 0–250°F, per Viega
  • Smart Connect shows an unpressed fitting during the pressure test, per Viega
  • 50-year limited fitting warranty for residential and commercial use, per Viega

What to watch

  • Needs one pipe free to slide
  • Fittings only; the press tool and jaws are separate

Viega lists the stop coupling from ½ to 2 inch: 78047, 78052, 78057, 78062, 78067 and 78072. The ½ inch is 1.61 inches long and the 2 inch is 3.31. They’re made from copper alloy C12200 with a peroxide-cured EPDM seal. [1]

Viega’s spec sets the prep. Cut with a wheeled tubing cutter or an approved copper cutter, square. Remove scale and dirt inside and out, wipe the end clean and dry, then ream the burrs. Insert the tube fully, mark it at the shoulder of the fitting, and check the fitting against the mark.

Smart Connect has a test range. Viega says water at 15 to 85 psi, or air at ½ to 45 psi, shows an unpressed fitting. It doesn’t replace the code test. [1]

Viega’s spec also says to install components with a pressure rating equal to or greater than the system’s operating pressure. ProPress copper is rated 300 psi, and the test limit is 600 psi. [1]

Best for
You’re joining new runs or replacing a section where one side can move.
Skip it if
Both pipe ends are locked in place. Use a coupling without a stop.
Sizes
½ and ¾ in.
Rating
300 psi, 0–250°F
Seal
EPDM
Warranty
50-year limited
Length
1.61 in. at ½ in.
Pack
5-pack
$22.94 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Elbows and tees for turns and branches

Viega 77317 90 degree elbow
Elbows and tees from Viega ProPress. Product photo: Amazon.

Elbows and tees round out a starter case. A 90° elbow handles a turn, and two of them can walk a line around an obstacle without a soldering job. A tee lets you add a branch to an existing line. [4]

Buy ½ inch first, then ¾ inch for the mains, water heater and supply runs. Keep them in the same brand as your couplings. [6]

The ½ inch elbow is Viega model 2916 and the tee is model 2918. For the ¾ inch sizes, the part numbers are 77022 for the elbow and 77387 for the tee, and Viega also lists a ½ x ½ x ¾ inch tee, 77382. [1]

Where it does well

  • Same ratings and warranty as the couplings
  • Elbows also save a joint when a repair needs an offset
  • Tees for adding a branch to a fixture or appliance

What to watch

  • ¾ in. versions are separate buys
  • Street and 45° elbows are separate part numbers

Viega’s ProPress submittal lists IAPMO/ANSI/CAN Z1117, NSF 61 and NSF 372 among system references. It warns that listings may not cover every item. I confirm the exact part against the current listing before specifying a certification. [1]

A street elbow saves a joint. Viega’s 2916.1 has one press end and one fitting end (FTG), which slides straight into another press fitting. The ½ inch is part 77347. The 45° elbow is model 2926, for offsets that don’t need a full turn. [1]

Viega’s spec allows one more option. Where approved, a change of direction can be made by bending Type K or L tube instead of adding an elbow. If that bent run is soft copper, Viega limits soft temper to ½ to 1¼ inch on ProPress. [1]

Elbows and tees are copper alloy C12200 with the same EPDM seal as the couplings. Viega rates them, like the rest of ProPress, at 300 psi operating and 0 to 250°F. [1]

Check dimensions by part number. Viega’s tee page notes that 77377, 77387, 77402, 77412, 77432 and 77437 use a different drawing from the rest of model 2918. [1]

Best for
You want the turns and branches covered for most bathroom and kitchen work.
Skip it if
You only do straight cut-out repairs. Couplings cover those.
Size
½ in. P x P
Body
Zero Lead copper
Rating
300 psi
Model
Viega 2916, 90° elbow
Pack
10-pack
$44.34 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

Bronze adapters for valves and heaters

Viega 79215 male threaded adapter
Bronze threaded adapters from Viega ProPress. Product photo: Amazon.

Sooner or later a repair ends at a threaded valve or a water heater nipple. A press-by-male or press-by-female adapter turns that into a press joint and a threaded joint, with no torch.

Viega makes these in Zero Lead bronze. Seal the threaded end the usual way; the press end seals with its own EPDM ring.

Viega lists the male adapter as model 2911ZL and the female as 2912ZL. The threaded side doesn’t have to match the press side. [5] [1]

Where it does well

  • Press on one end, pipe thread on the other
  • Zero Lead bronze, per Viega
  • Male and female cover valves, unions and water heater nipples

What to watch

  • Unions for a water heater are separate parts (2960ZL)
  • Thread sealant still needed on the threaded end

Viega makes ½ inch press by ¾ inch NPT in male (79220) and female (79305), and ½ by ⅜ inch in male (79210) and female (79295). When both sides are ¾ inch, it’s 79230 male or 79315 female, and ¾ inch press by ½ inch NPT is 79225 male or 79310 female. [1]

Viega’s data sheet names the metal: Zero Lead silicon bronze, C87710 when cast or C87700 when machined. Threaded ends follow ASME B1.20.1, the standard for general purpose pipe threads. [1]

Viega’s spec gives the threading rule: pipe joint compound or Teflon tape on the male threads only, and tighten with a wrench and a backup wrench.

For a water heater or a valve you’ll want to remove later, Viega also makes bronze unions: 2960ZL press by press, 2962ZL press by female thread and the 2967ZL dielectric union. The ½ inch press union, 79125, is 2.84 inches long. [1]

Viega makes the male adapter with a fitting end too, model 2911.1ZL. That end slides into another press fitting, so the adapter needs no press joint of its own on that side. [1]

The bronze adapters carry the same ProPress ratings as the copper fittings: 300 psi operating and 0 to 250°F, with a 600 psi test limit. [1]

Best for
You tie into threaded valves, water heaters or old threaded work.
Skip it if
Everything you touch is copper to copper.
Connection
½ in. press x ½ in. NPT
Body
Zero Lead bronze
Model
Viega 2911ZL, male adapter
Threads
ASME B1.20.1
Pack
Pack quantity shown on Amazon
$16.58 at AmazonPrice as of Nov 22, 2026, 9:30 AM EST · low stock then
Check price on Amazon

New. Low stock at the Nov 18, 2026 check. Stock can change.

The starter list at a glance

FittingViega ½ in.Viega ¾ in.What it’s for
Coupling, no stop78172 [1]78177 [1]Repairs between fixed pipes
Coupling, with stop78047 [1]78052 [1]Joining tube where one side can move
90° elbow77317 [1]Separate buyTurns and offsets
Tee77377 [1]Separate buyAdding a branch
Male adapter79215 [1]Separate buyInto threaded fittings
Female adapter79300 [1]Separate buyOnto threaded nipples and valves

Source: [1]. Part numbers and specifications follow the maker’s document.

Catalog numbers from the Viega listings above. For brand-by-brand ratings, see the copper press fittings guide. [1]

Coupling part numbers and lengths by size

SizeWith stop (2915)No stop (2915.3)Length
½ in.78047 [1]78172 [1]1.61 in. [1]
¾ in.78052 [1]78177 [1]2.01 in. [1]
1 in.78057 [1]78182 [1]1.97 in. [1]
1¼ in.78062 [1]78187 [1]2.20 in. [1]
1½ in.78067 [1]78192 [1]2.99 in. [1]
2 in.78072 [1]78197 [1]3.31 in. [1]

Source: [1]. Part numbers and specifications follow the maker’s document.

Both kinds share a body length at each size on Viega’s drawings, so one bin holds both. Label the bins anyway. From the outside the only difference is the stop inside, and a stop coupling won’t slide over the gap in a fixed-pipe repair.

Stock follows your jaws. A compact tool presses ½ to 1¼ inch ProPress, so the first four rows cover every size it can press. [1] [10]

What each starter fitting is made of

FittingBodySealNotes from Viega
Couplings, elbows, teesCopper, UNS C12200 [1]Peroxide-cured EPDM300 psi, 0–250°F [1]
Threaded adaptersZero Lead silicon bronze C87710 (cast) or C87700 (machined) [1]Peroxide-cured EPDMThreads to ASME B1.20.1 [1]
UnionsZero Lead bronzePeroxide-cured EPDM2960ZL, 2962ZL, 2967ZL dielectric [1]
2½–4 in. fittingsCopper or bronzeEPDM plus 420 stainless grip ring and PBT separator [1]Check the grip ring is in place

Source: [1]. Part numbers and specifications follow the maker’s document.

FittingViega modelWhy it earns a bin
90° street elbow2916.1 (½ in. 77347) [1]Fitting end goes straight into another fitting; one less joint
45° elbow2926 [1]Small offsets around a stud or another line
Union, press x press2960ZL (½ in. 79125) [1]Lets a part come back out later
Dielectric union2967ZL [1]Press by female thread, listed as a dielectric union
Female adapter, fitting end2912.1ZL [1]Bronze FTG x FPT, no press joint on that side
Reducer2915.2 [1]Steps a line down a size
Ball valve2971.1ZL [1]Zero Lead bronze, press both ends

Source: [1]. Part numbers and specifications follow the maker’s document.

All of these are on Viega’s ProPress submittal list. Add them as your jobs ask for them, not all at once. A street elbow cuts out a joint, and a union lets a part come back out without cutting.

Which bins each common job pulls from

Most service calls use two or three bins from the starter list. This is how the list maps to the work.

JobPull fromWhy those
Pinhole in a ½ in. line between two strapsTwo ½ in. no-stop couplings (78172) and a short piece of tube [2]Neither pipe end can move, so both couplings have to slide over the cut
Swap an angle stop or a threaded valve½ in. male adapter (79215) or female adapter (79300) [5] [1]Press onto the copper, thread into the valve; no torch near the wall
Water heater change on ¾ in. lines¾ in. stop couplings (78052), plus ¾ in. adapters bought for the heater [1]The heater side can move, so stop couplings seat by feel
Add a branch for an ice maker or hose bib½ in. tee (77377) and ½ in. 90° elbows (77317) [4] [1]A tee for the branch, elbows to turn it where it needs to go
Jog around a stud or another lineTwo ½ in. 90° elbows, or two 45° elbows (2926) once you stock them [1] [4]Two fittings make the offset; 45s keep it short [1]
New ½ in. run in an open wall½ in. stop couplings (78047), elbows and tees [3]Every joint can be pushed home to the stop, so marking is quick

Source: [1]. Part numbers and specifications follow the maker’s document.

Read the list top to bottom and the pattern is plain: the ½ in. no-stop coupling is the one bin you can’t do without on repair calls, and the ¾ in. bins earn their space on water heaters and mains. Elbows and tees only matter once you start changing the route of a line, not just fixing it. [1]

How to bin, label and restock the starter case

BinPack on the listingRestock when
½ in. no-stop coupling, 781725-pack [7]Two left: one repair takes two
½ in. stop coupling, 780475-pack [7]Two left
½ in. 90° elbow, 7731710-pack [7]Four left: an offset takes two
½ in. male adapter, 79215Check quantity on AmazonTwo left
¾ in. no-stop and stop couplings, 78177 and 78052Check the pack size on the listingTwo left in each

Source: [1]. Restock quantities are my planning choices; pack sizes follow the current Amazon listing.

Keep each size and kind in its own labeled bin. A stop and a no-stop coupling share a body length at each size on Viega’s drawings, so the label is the only quick way to tell them apart. Grab the wrong one on a fixed-pipe repair and it won’t slide over the gap.

Keep fittings in their bags until you use them. Viega’s install steps start with checking that the seal is in place and undamaged, and grit in a loose bin is the easy way to fail that check. The restock points are my call, set so the last two of anything never leave you short on a two-fitting repair.

Prep, tube and insertion depth

This page is about what to stock. How to cut, clean, ream and mark the tube, which copper ProPress may go on, and how deep each size seats are covered step by step in my press fitting insertion depth guide. If the line won’t drain dry, read can you press a wet line before you open a bag.

Four rules before you load the van

Match fittings to your jaws

A compact tool like the RP 251 or M12 presses ½ to 1¼ inch ProPress. Stock sizes your jaws cover. See RIDGID ProPress jaws and best press tools. [1] [10]

One brand per joint

Viega’s warranty excludes failures caused by components from other makers. Keep each joint one brand; see NIBCO vs Viega.

Not for gas

These EPDM-seal fittings are for water and heating. Gas press fittings are a different line with a different seal.

No-name assortments

If a kit’s listing doesn’t name a fitting maker whose tool chart lists your jaws, skip it. You can’t check what you can’t identify.

Questions people ask

What press fittings should I keep on the van?

Couplings with and without a stop, 90° elbows, tees and male and female threaded adapters, in ½ and ¾ inch. Keep them one brand that your tool’s jaws are listed for. [1]

What’s the difference between a coupling with and without a stop?

A coupling with a stop has a shoulder in the middle that sets the insertion depth, so one pipe must be free to move. A coupling without a stop slides fully onto one pipe and back over the joint, which is what you need when both ends are fixed.

How many of each fitting should I start with?

My call: one 5-pack of ½ in. no-stop couplings, one 5-pack of ½ in. stop couplings, one 10-pack of ½ in. elbows and enough ½ in. male adapters for the planned valve connections, then the ¾ in. couplings. That covers a pinhole repair, a valve swap and a short reroute without a supply-house run. [9]

Can I mix press fitting brands?

On the same job, joint by joint, yes. Inside one joint, no: Viega excludes failures caused by other makers’ components. I keep the joint within one maker’s approved system.

What pressure are press fittings rated for?

Viega rates its ProPress copper fittings at 300 psi and 0 to 250°F. I check NIBCO PC601 against NIBCO’s own technical sheet instead of applying Viega’s rating to it. Check the rating of each fitting you stock, because a repair is only as strong as its lowest-rated part. [1] [6]

Can you press a wet line?

Viega says ProPress lets installers join wet connections, which is a big part of why press fittings are used on repairs. See can you press a wet line.

Can you ProPress under a slab?

Viega says ProPress is approved above and below ground, but per code you need your local inspector’s approval before installing it below ground.

Are cheap press fitting kits on Amazon okay?

Only if you can confirm the brand’s fittings are approved for your tool and jaws and listed to the standards your inspector expects. If the listing doesn’t say, buy a known brand.

What is a street elbow in press fittings?

One end presses onto tube and the other end (FTG) is sized like tube, so it slides straight into another fitting. Viega’s ½ inch 90° street elbow is part 77347, model 2916.1. [1]

Do I put thread sealant on a press adapter?

On the threads only, and only the male threads. Viega’s spec says pipe joint compound or Teflon tape on the male threads, tightened with a wrench and a backup wrench. The press end seals with its own EPDM ring.

What sizes do Viega no-stop couplings come in?

Viega’s submittal lists model 2915.3 from ½ to 2 inch (78172 to 78197) and 2½ to 4 inch (20728 to 20738). [1]

Are ProPress threaded adapters lead-free?

Viega makes them in Zero Lead silicon bronze (C87710 cast or C87700 machined), and names NSF 372 and CSA Low Lead in its system submittal. I check the exact fitting’s current listing before relying on a certification. [1]

Does Viega make a press union?

Yes. Viega’s submittal lists bronze unions in press by press (2960ZL), press by female thread (2962ZL) and a dielectric union (2967ZL). [1]

Can I bend copper instead of using a press elbow?

Where your inspector approves it, yes. Viega’s spec allows a change of direction by bending Type K or L tube. Soft copper on ProPress is limited to ½ to 1¼ inch. [1]

How I picked these

I compared 4 fittings: Viega 78172, 78047, 77317 and 79215, using the Viega ProPress Systems SM-PP 0926 submittal and the maker’s exact item pages. I checked each Amazon listing for New condition and stock on November 15, 2026. [7] [1]

Why trust me

I’m Isaac Daniels, a licensed journeyman plumber in Georgia. I’ve installed Viega ProPress, NIBCO Press and ApolloPress fittings on real jobs, and if I could stock only one brand it’d be Viega ProPress.

How I pick

My CPSC brand search for Viega and NIBCO on November 15, 2026 found no matching recalls in its records since 2018. My bin restock points are planning choices, rather than maker requirements. The adapter quantity is the quantity on its current Amazon listing. [8]

Sources

  1. Viega ProPress Systems SM-PP 0926, system data page 3, installation/specification pages 4 to 10, dimensions pages 11 to 32, limited warranty pages 33 to 34.
  2. Viega 78172 exact item page, connections, seal and dimensions.
  3. Viega 78047 exact item page, connections, seal and dimensions.
  4. Viega 77317 exact item page, connections, seal and dimensions.
  5. Viega 79215 exact item page, connections, seal and dimensions.
  6. NIBCO PC601 catalog, repair-coupling identity and separate-brand stock alternative.
  7. Amazon listings: current product names and pack quantities, checked November 15, 2026. The 79215 pack quantity is whatever the selected listing states.
  8. CPSC public recall records: Viega and NIBCO brand search, November 15, 2026, records since 2018, no matching recalls.
  9. Stock planning: restock at two remaining couplings or adapters and four elbows. These are my starting recommendations for two-fitting repairs, not maker requirements.
  10. Viega Tool Matrix TD-TL 0326, ProPress compact-tool and jaw ranges.

Related guides