M12 press tool: 2473 vs 2573

What changed, and what to buy now.

As an Amazon Associate I earn from qualifying purchases. Links go to listings sold by Amazon.com.

On this page
  1. The models
  2. Is it discontinued?
  3. What it presses
  4. Side by side
  5. 2473 vs 2573
  6. Buy now or wait
  7. Jaw part numbers
  8. Light codes
  9. How to press
  10. Heat, cold, duty
  11. Batteries
  12. Service and warranty
  13. ONE-KEY
  14. Fitting maker rules
  15. How to choose
  16. Questions
  17. How I pick

Quick answer

Milwaukee discontinued the M12 2473 press tool, not the M12 line. The ONE-KEY 2573 replaced it; your jaws and packs carry over. For ½ to 1 in. copper, the 2473-22 kit and the current 2573-22 kit both cover it. Milwaukee’s tool warranty matters here: it covers the original purchaser from an authorized distributor. For 1½ or 2 in. copper, get an M18.

Milwaukee 2473-22 kitReference (not linked): shown for comparison only.

The M12 press tool models compared

Two tools and one jaw, each for a different job, shown as references.

Milwaukee M12 kit 2473-22

Reference (not linked): shown for comparison only.

Milwaukee M12 tool 2473-20

Reference (not linked): shown for comparison only.

Milwaukee ½ in. jaw 49-16-2450

Reference (not linked): shown for comparison only.

ToolKey specsFits ifSkip it if
Milwaukee M12 kit 2473-22 (reference, not linked)3.8 lb, 5,400 lbs force, ½, ¾, 1 in. jaws, 1¼ in. max CTS copper, 32,000 crimps, 5-yr tool warrantyYou press ½ to 1 in. copper on service calls, water heaters and repipes, and you want a complete kit that runs on the M12 packs already in your truck.You need press logs for inspected commercial work: wait for a 2573-22. You press 1½ or 2 in. copper: buy an M18. You press PEX or refrigeration lines: the kit jaws won’t do it.
Milwaukee M12 tool 2473-20 (reference, not linked)3.8 lb, 5,400 lbs force, No jaws, 1¼ in. max CTS copper, 32,000 crimps, 5-yr tool warrantyYou already own M12 jaws, or RIDGID compact jaws on Milwaukee’s list, and you want a second tool for a helper’s truck or a backup while the first one is at service.This is your first press tool for ½ to 1 in. copper. The 2473-22 kit has those jaws in the box.
Milwaukee ½ in. jaw 49-16-2450 (reference, not linked)½ in. CTS-V, M12 only, 2473 and 2573, Copper, Made in Germany (listing), 2-yr jaw warrantyYour ½ in. jaw is cracked, worn or lost, or you want a spare of the size you press most.You need a size or material the kit jaws don’t cover. Look up that system on the jaw map first.

Is the Milwaukee M12 press tool discontinued?

The 2473 is. Milwaukee’s pages for the 2473-20 and 2473-22 both read that the product is no longer available and has been replaced, with a link to the 2573-20 and 2573-22. Milwaukee still lists the 2573 on M12 batteries, so the M12 press tool line goes on.

Discontinued means Milwaukee stopped making that model. It isn’t a recall, and it doesn’t stop a tool from pressing. Our search of the CPSC recall database on Oct 20 found that none of the Milwaukee Tool recalls there involve an M12 press tool, its jaws or M12 packs.

Keep using your 2473

It presses the same fittings the 2573 does, with the same jaws, per Milwaukee’s 2026 matrix.

Keep your jaws

The 2573-22 kit ships with the same 49-16-2450, 2451 and 2452 copper jaws.

Keep your packs

Both tools run on any M12 battery, per Milwaukee’s pages.

Keep your receipt

Milwaukee’s warranty covers the original purchaser and asks for proof of purchase.

Don’t swap in M18 jaws

Milwaukee says M12 and M18 jaws use different locking mechanisms.

Expect new 2473 stock to thin out over time, since Milwaukee lists it as no longer available.

Which fittings the M12 presses, and with which jaw

The kit jaws are CTS-V jaws for ½ to 1 in. Other systems need their own jaws or rings. This map covers every fitting system in Milwaukee’s 2026 compatibility matrix, M12 column, which lists the 2573-20 and the discontinued 2473-20 together.

CTS-V jawskit: ½–1 in.; 1¼ in. jaw extra Viega ProPress, ProPress G, ProPress stainless (jaws and rings) Mueller Streamline PRS (jaws and rings) ApolloPress copper (jaws and rings) NIBCO copper, the ½ to 2 in. line (jaws and rings) >B< Press by Conex Bänninger (jaws and rings) AnvilPress copper (jaws) FW Webb PurePro, Ferguson FNW and PROFLO (jaws) Wolverine Brass copper (jaws) IPS-P jaws and ringscarbon steel; to 1 in. Viega MegaPress and MegaPress G Mueller Streamline STL and STL-G Apollo PowerPress NIBCO BenchPress PEX jawsto 1½ in. Viega PureFlow: RIDGID compact PureFlow jaws ASTM F1807 and F2159 crimp: M12 PEX crimp jaws (no ⅜ or ⅝ in.) Refrigeration jawsACR and HVAC/R Mueller Streamline ACR to ⅞ in.: Streamline ACR jaws ZoomLock MAX and >B< MaxiPro, ¼ to 1⅛ in.: their own jaws RLS HVAC/R, ¼ to 1⅜ in. line: RIDGID RLS RJ series jaws Not designed for the M12M18 tools only MegaPress XL and NIBCO copper 2½ to 4 in.: M18 Long Throw only ProPress XL-C, XL-S and other 2½ to 4 in. lines: M18 1½ and 2 in. copper or ProPress stainless: M18 Aalberts SmartPress, AnvilPress stainless, Merit StainlessPress: M18 Source: Milwaukee 2026 Press Tool Compatibility Matrix, M12 column (2573-20; discontinued 2473-20), read Oct 20, 2026. CTS-V jaws · kit: ½–1 in.; 1¼ in. jaw extra • Viega ProPress, ProPress G and ProPress stainless (jaws and rings) • Mueller Streamline PRS (jaws and rings) • ApolloPress copper (jaws and rings) • NIBCO copper, ½ to 2 in. line (jaws and rings) • >B< Press, Conex Bänninger (jaws and rings) • AnvilPress copper (jaws) • FW Webb PurePro, Ferguson FNW and PROFLO (jaws) • Wolverine Brass copper (jaws) IPS-P jaws and rings · carbon steel; to 1 in. • Viega MegaPress and MegaPress G • Mueller Streamline STL and STL-G • Apollo PowerPress • NIBCO BenchPress PEX jaws · to 1½ in. • Viega PureFlow: RIDGID compact PureFlow jaws • F1807 and F2159 crimp: M12 PEX crimp jaws (no ⅜ or ⅝ in.) Refrigeration jaws · ACR and HVAC/R • Mueller Streamline ACR to ⅞ in.: Streamline ACR jaws • ZoomLock MAX, >B< MaxiPro, ¼ to 1⅛ in.: their own jaws • RLS HVAC/R, ¼ to 1⅜ in.: RIDGID RLS RJ series jaws Not designed for the M12 · M18 tools only • MegaPress XL, NIBCO copper 2½ to 4 in.: M18 Long Throw only • ProPress XL-C, XL-S and other 2½ to 4 in. lines: M18 • 1½ and 2 in. copper or ProPress stainless: M18 • Aalberts SmartPress, AnvilPress stainless, Merit StainlessPress: M18 Source: Milwaukee 2026 Press Tool CompatibilityMatrix, M12 column, read Oct 20, 2026.
Every fitting system in Milwaukee’s 2026 Press Tool Compatibility Matrix, grouped by the jaw the M12 needs. “Jaws and rings” means Milwaukee lists both for that system. Read Oct 20, 2026.

Read the limits by material. Plumbing copper and ProPress stainless stop at 1¼ in., and that size needs the 49-16-2453 jaw, sold separately. Carbon steel stops at 1 in., PEX at 1½ in., and RLS refrigeration copper runs to 1⅜ in. with RIDGID RJ jaws.

Nothing from 1½ in. copper upward is on the M12’s list. The matrix sends most of it to the standard M18 tool, but MegaPress XL and NIBCO’s 2½ to 4 in. copper need the M18 Long Throw.

The matrix also covers jaws from another maker. Milwaukee lists RIDGID compact jaws for Viega PureFlow PEX and RIDGID’s RJ series jaws for RLS refrigeration fittings. On the matrix, those are the jaws listed for those two systems.

The three models side by side

Milwaukee’s numbers, one row per model. On a phone, the table scrolls sideways.

ModelPhotoWhat you getFitsShort pros / consAmazon
2473-22 kit
Tool, 3 jaws, 2 packs
Tool, ½ to 1 in. jaws, two CP1.5, charger, caseAny M12 packReady to press / DiscontinuedReference (not linked)
2473-20 tool
No jaws
Tool; Amazon doesn’t list the box contentsM12 jaws, listed RIDGID compact jawsUses jaws you own / No jawsReference (not linked)
49-16-2450 jaw
½ in. CTS-V
One ½ in. copper jaw2473 and 2573Exact kit part / M12 onlyReference (not linked)

Green marks a strength and amber marks a trade-off. Box contents come from Milwaukee’s product pages.

What changed from the 2473 to the 2573

Same size class, same jaws, same battery line. The differences are in the box and inside the tool. Every cell below comes from Milwaukee’s own product pages and parts list, read Oct 20, 2026.

Item2473 (discontinued)2573 (current)What it means for you
Status at MilwaukeeNo longer availableCurrent modelNew 2473s are leftover stock, still sold
Kit jaws49-16-2450, 2451, 245249-16-2450, 2451, 2452Same three part numbers
Packs in the boxTwo CP1.5, 48-11-2401Two CP2.0, 48-11-2422Bigger packs in the new box
Charger in the box48-59-240148-59-2401Same charger
Runs onAll M12 packsAll M12 packsYour packs carry over
Service interval32,000 crimps37,000 press cyclesAbout 16% more presses per service
ONE-KEYNoneTracking, logs, lockoutMatters for fleets and inspected jobs
Battery checkGreen LED flashes when the charge is too lowWon’t start a press it can’t finishOnly the 2573 promises to block a half press
CaseHard casePackout tool case 48-22-8450 (2573-20 parts list)New tool stacks with Packout boxes
Max CTS plumbing copper1¼ in. with jaw 49-16-24531¼ in. CTSSame reach
Tool warranty5 years5 yearsSame

From Milwaukee’s 2473-20, 2473-22, 2573-20 and 2573-22 pages and the 2573-20 parts list PN0003467 (May 2026), read Oct 20, 2026. The 2573-22 page lists its pack as 48-11-2420 in one place and 48-11-2422 in another; the table uses the 2573-20 page’s number.

The service count is the change you’ll notice. A shop pressing 40 joints a day, 250 days a year, puts 10,000 presses on a tool. On that projection, which counts presses only, that’s a little over three years to 32,000 and a little under four to 37,000. The manual’s six-month to one-year maintenance visits are a separate schedule.

The other changes are about packs and managing tools. A solo plumber gives up bigger packs, a higher service count and ONE-KEY by buying a 2473, and keeps the same jaws and reach.

Buy a 2473 now or wait for a 2573?

Both press the same joints. The choice comes down to whether you’ll use ONE-KEY and whether you can get a 2573 new from a seller you trust.

Your situationMy pickWhy
One truck, ½ to 1 in. copper, need a tool this week2473-22 kit nowSame jaws and reach; check the seller against Milwaukee’s warranty terms
Already own a working 2473Keep itDiscontinued isn’t a recall; it presses the same fittings
You own M12 jaws and want a backup2473-20 nowCovers you while the first tool is at service
Company with several trucks and a tool managerWait for a 2573ONE-KEY tracking, logs and remote lockout
Inspected commercial jobs that want press recordsWait for a 2573Time-stamped data logs, per Milwaukee
Regular 1½ or 2 in. copperNeither M12Off the M12 list; a 2573 won’t change that. See M12 vs M18
MegaPress XL or NIBCO 2½ to 4 in. copperNeither M12Milwaukee lists the M18 Long Throw for these
PEX to 1½ in.Either M12, with PEX jawsThe kit jaws don’t press PEX

If you wait for the 2573, note that Milwaukee’s tool warranty covers the original purchaser from an authorized distributor. Check that the listing names the exact 2573 model and kit contents, not a part sold “for Milwaukee.”

Whichever you buy, your jaws move with you. That’s the money in a press tool kit.

M12 press jaws and part numbers

Part numbers are stamped on the jaw. Match them to this list, not to a photo.

JawPart numberWhere it comes fromNotes
½ in. CTS-V copper49-16-24502473-22 and 2573-22 kitsFits both M12 tools
¾ in. CTS-V copper49-16-24512473-22 and 2573-22 kitsFits both M12 tools
1 in. CTS-V copper49-16-24522473-22 and 2573-22 kitsFits both M12 tools
1¼ in. CTS-V copper49-16-2453Sold separately (2473-20 page)Largest CTS plumbing-copper size
Steel, IPS-PMilwaukee IPS-P pivoting jaw kitSold separatelyMegaPress and others, to 1 in.
RIDGID compact ProPress16958, 16963, 16978, 31228Milwaukee’s 2026 matrixCopper, on the M12
RIDGID compact PureFlow17003, 17008, 17013, 17018, 19813, 22683, 22688Milwaukee’s 2026 matrixViega PureFlow PEX
RIDGID compact F180722958, 22968, 22973, 22978Milwaukee’s 2026 matrixPEX crimp rings
RIDGID RJ series770210 to 770219Milwaukee’s 2026 matrixRLS refrigeration fittings
Any M18 jawWon’t fit2573 FAQDifferent locking mechanism

The Milwaukee numbers come from its 2473-20, 2473-22 and 2573-22 pages. The RIDGID numbers come from the final page of Milwaukee’s 2026 Press Tool Compatibility Matrix. We read both on Oct 20, 2026. A jaw missing from that matrix isn’t cleared for these tools, so match the part number exactly.

If you’ve got a bag of RIDGID jaws from an older compact tool, this list can save you a jaw set. RIDGID’s standard-size jaws aren’t on the M12 list; only the compact ones are. Our RIDGID ProPress jaws guide explains which series is which.

What the lights on the M12 press tool mean

The 2473 talks to you with a green LED, a red LED and a fuel gauge. Here’s every state in its operator’s manual.

Green Red What you see What it means What to do Green on after a pressThe press cycle finishedMove on to the next joint. Green flashingThe pack can't finish a pressCharge or swap the battery. Red flashingTool is outside -10 to 50 °CWarm or cool it to 14 to 122 °F. Red onDevice faultRetry; if it stays lit, send it in. Green and red alternatingService is dueSend tool, charger and pack in. steadyflashingoff Source: Milwaukee 2473-20 operator's manual 58-14-2490d2, press steps and troubleshooting table. The 2573 has its own manual. Green on after a pressThe press cycle finishedMove on to the next joint. Green flashingThe pack can't finish a pressCharge or swap the battery. Red flashingTool is outside -10 to 50 °CWarm or cool it to 14 to 122 °F. Red onDevice faultRetry; if it stays lit, send it in. Green and red alternatingService is dueSend tool, charger and pack in. steadyflashingoff Source: Milwaukee 2473-20 operator's manual58-14-2490d2. The 2573 has its own manual.
Status lights from Milwaukee’s 2473-20 operator’s manual, 58-14-2490d2. The Fahrenheit range is converted from the manual’s -10 to 50 °C.

To check the pack, press and release the start button and the fuel gauge lights up. When one light on the gauge flashes, the pack is at the end of its charge. Check it before a run of presses, not after one stalls.

A steady red light is the one to take seriously. Press start again; if the tool still won’t run, it goes back to a Milwaukee service facility with its charger and pack.

How to make a press with the M12

This is the press cycle from the 2473 manual, plus the two checks it asks for first. The fitting maker’s own steps for prep and insertion still apply.

  1. 1
    Check the jaw, the pipe and the pack

    Put on safety glasses with side shields. Look the jaw over for cracks or damage, and don’t use a damaged one. The manual also says to discard any pipe or fitting with cracks or wear. Press and release start to read the fuel gauge.

  2. 2
    Wake the tool

    A quick press and release of the start button turns it on. It shuts off by itself after 30 minutes without use.

  3. 3
    Set the jaws on the fitting

    Open the jaws and place them around the fitting, the way the fitting maker shows.

  4. 4
    Hold it and start

    Hold the tool securely with your hands away from the crimping head, then press and hold the start button. The green LED goes out.

  5. 5
    Let it finish

    The automatic cycle begins. Release the button and keep holding the tool steady until it switches off and the green LED lights.

  6. 6
    Cancel if you must

    Press and hold the release button. Keep holding the tool until the jaws open and it turns off.

Cut, deburr and mark insertion depth before any of that, following the fitting maker’s instructions. Our insertion depth marks guide covers that part. A press tool only finishes the joint you set up. The green light means the press cycle finished; it does not prove the joint is leak-free, so follow the fitting maker’s inspection and test instructions.

Heat, cold and long runs

The manual gives one temperature range and one cool-down rule. Here’s how they play out on a job.

ConditionWhat the 2473 manual saysWhat to do on the job
Tool below -10 °C (14 °F)Red LED flashes; outside its rangeWarm it in the cab before pressing
Tool above 50 °C (122 °F)Red LED flashes; outside its rangeShade it; don’t leave it on a hot dash
30 minutes of continuous pressingRest it at least 15 minutesRare outside a production fixture
Normal plumbing usePress freely and watch the LEDsNo set rest breaks
30 minutes idleTurns off on its ownQuick press of start to wake it

The manual’s own example for continuous use is a manufacturing fixture, not a house. On a repipe you’ll stop to cut, deburr and mark between presses, which is the “normal use” case. Watch the lights and let them tell you.

Heat is the likelier problem in a Southern summer. A tool left on a dashboard in the sun can climb past 50 °C, and the red flash is your cue to cool it.

Batteries for the M12 press tool

PackWhere it shows upFits the 2473?Fits the 2573?
M12 CP1.5, 48-11-2401Two in the 2473-20 and 2473-22 boxesYesYes, all M12 packs
M12 CP2.0, 48-11-2422Two in the 2573-20 boxYes, all M12 packsYes
Any other M12 REDLITHIUM packYour other M12 toolsYesYes
M18 packsM18 toolsNoNo

From Milwaukee’s 2473-20 and 2573-20 pages, which both say the tool works with all M12 batteries and chargers, read Oct 20, 2026.

None of the Milwaukee documents we read gives a presses-per-charge figure for either tool, so I won’t guess at one. What it does say is that the 2473 packs recharge in 30 minutes. With two packs and one charger, you can keep one on the charger and one in the tool.

If the tool won’t start or seems weak on a full pack, the manual says to clean the pack’s contacts first. If that doesn’t fix it, send the tool, charger and pack in.

Service, calibration and warranty

A press tool goes back to Milwaukee on a schedule. Here’s what each document says, side by side.

Topic24732573Source
Presses between service32,000 crimps37,000 press cyclesProduct pages
Calibration warningVisual indicator on the toolLight for full cycle or calibration dueProduct pages
Routine maintenanceEvery 6 months to 1 year, by useIts own manual2473 manual
Service lightRed and green alternateIts own manual2473 manual
What to sendTool, charger and pack (repairs: jaws and rings too)Tool, charger and batteries, with a description2473 manual; 2573 parts list
Tool warranty5 years, original purchaser5 years2473 manual; 2573 pages
Battery and jaw warranty2 years (2473-20 page)2 years (2573-22 page)Product pages
Service line1-800-729-38781-800-729-38782573 parts list; matrix

Two warranty rules from the manual are easy to miss. You ship the tool to a Milwaukee service center freight prepaid and insured, with proof of purchase. And repairs by anyone other than Milwaukee’s authorized people, along with misuse, wear, lack of maintenance or accidents, aren’t covered.

The 2573 parts list adds one more: only the maintenance in its manual is yours to do. Anything else could void the warranty.

Cleaning is simple. The manual says mild soap and a damp cloth on the tool, pack and charger, and keep the handle dry and free of oil. It warns against gasoline, thinners, chlorinated solvents and ammonia, which can harm the plastics.

What ONE-KEY adds to the 2573

ONE-KEY is Milwaukee’s tool-tracking system. On the 2573 it does three things the 2473 can’t.

Time-stamped press logs

Milwaukee says the 2573 keeps data logs for reporting, which helps when a job wants a record of each press.

Tracking

Milwaukee’s FAQ says you can track the tool, monitor its use and generate reports.

Remote lockout

Milwaukee says you can lock the tool remotely, which helps if it walks off a site.

A coin cell to replace

The 2573-20 parts list shows a CR2032 coin cell behind its own door.

Not on the 2473

The 2473 has no ONE-KEY at all; its lights are its whole report.

For one truck, I’d call ONE-KEY a nice-to-have. You already know where your tool is, and the green light tells you each press finished. For a company running several trucks, logs and lockout are a real reason to wait for a 2573.

Our M12 vs M18 press tool comparison covers ONE-KEY on the M18 2922 too.

What Milwaukee’s matrix asks of you

The matrix ends with a short list of rules. They put the last check on the installer, not the tool.

Rule in the matrixWhat it means on the job
Tools are approved only with the jaws and rings listedUse the jaw part numbers above, nothing else
The installing contractor checks pipe and fitting compatibilityRead the fitting maker’s own tool list too
Install fittings per the fitting maker’s instructionsTheir prep, depth and inspection steps apply
Jaw cleanliness and inspection are the installer’s responsibilityWipe and look at the jaw before you press

Viega ProPress, NIBCO Press and Apollo fittings are all on the M12’s copper list. Even so, each fitting maker publishes its own tool and jaw list. Find your tool and jaw part number there before a job, especially on an unfamiliar brand.

Picking the fitting brand is its own decision. Our copper press fittings guide compares the copper lines, and NIBCO vs Viega ProPress covers the two most common ones.

How to choose an M12 press tool

QuestionIf yesIf no
Is every system you press on the M12 side of the jaw map, inside its size? Check copper and ProPress stainless to 1¼ in., RLS to 1⅜ in., Streamline ACR to ⅞ in., ZoomLock MAX and MaxiPro to 1⅛ in., PEX to 1½ in. (no ⅜ or ⅝ in. crimp), carbon steel to 1 in.Keep goingGet the tool the matrix lists for that system: usually an M18, and the M18 Long Throw for MegaPress XL or NIBCO 2½ to 4 in.
Does your company need press logs or remote lockout?Wait for a 2573 from a seller you trustKeep going
Do you already own M12 jaws or listed RIDGID compact jaws?2473-20, no jawsKeep going
Is your work plumbing copper or ProPress stainless, ½ to 1¼ in.?2473-22 kit, since the matrix lists CTS-V jaws for both; add the 49-16-2453 jaw for 1¼ in.2473-20 plus the jaws the matrix lists for your system: PEX, IPS-P for carbon steel, or ACR

For every brand, not just Milwaukee, start with our best press tool guide. If you’re weighing Milwaukee against RIDGID’s compact tool, read RIDGID vs Milwaukee press tool. Still deciding whether pressing is worth it over a torch? See ProPress vs soldering.

Questions people ask

Is Milwaukee discontinuing the M12 press tool?

Only the 2473 model. Milwaukee’s 2473-20 and 2473-22 pages say they’re no longer available and were replaced by the 2573-20 and 2573-22, which still run on M12 batteries.

What replaced the Milwaukee 2473-22?

The 2573-22, the M12 Force Logic press tool kit with ONE-KEY and ½ to 1 in. CTS-V jaws. Milwaukee’s 2473-22 page links to it as the replacement.

Do my 2473 jaws fit the 2573?

Yes. The 2573-22 kit ships with the same 49-16-2450, 2451 and 2452 jaws as the 2473-22, and Milwaukee’s 2026 matrix lists both tools in one M12 column.

Can I still use and service my 2473?

Yes. Discontinued isn’t a recall. The manual sends it to a Milwaukee service facility for maintenance and repairs, and Milwaukee’s service line is 1-800-729-3878.

What does a flashing green light mean on the M12 press tool?

The battery doesn’t have enough charge to finish a press. The 2473 manual says to charge it, or swap in a charged pack.

What does a red light mean on the Milwaukee M12 press tool?

Flashing red means the tool is outside -10 to 50 °C. Steady red is a device fault: retry, and if it stays lit, return the tool, charger and pack for repair. Red and green alternating means service is due.

Does the M12 press tool need ONE-KEY to work?

No. The 2473 has no ONE-KEY at all and presses with its lights as feedback. On the 2573, ONE-KEY adds tracking, time-stamped logs and remote lockout.

Can the M12 press tool do 1¼ in. copper?

Yes, with a 1¼ in. jaw. Milwaukee’s 2473-20 page names jaw 49-16-2453, sold separately, and the 2573 FAQ lists 1¼ in. CTS copper as its largest CTS size.

Can the M12 press tool press PEX?

Yes, with PEX jaws, up to 1½ in. Milwaukee’s matrix lists M12 PEX crimp jaws for F1807 and F2159 fittings and RIDGID compact jaws for Viega PureFlow.

Which battery comes with the Milwaukee 2573?

Milwaukee’s 2573-20 page lists two M12 REDLITHIUM CP2.0 packs, 48-11-2422, and the 48-59-2401 charger. The 2473 kits came with two CP1.5 packs.

How long can I run the M12 press tool before it needs a rest?

The 2473 manual says 30 minutes of continuous pressing needs at least 15 minutes to cool. For normal plumbing it says to press freely and watch the lights.

Is the M12 press tool good for HVAC?

With the right jaws. Milwaukee’s matrix lists Streamline ACR to ⅞ in., ZoomLock MAX and Conex Bänninger MaxiPro to 1⅛ in., and RLS fittings with RIDGID RJ series jaws.

How I picked these

Why trust me

I’m Isaac Daniels, and I hold a Georgia journeyman plumber license, #JP507711.

How I pick

  • Facts from Milwaukee’s product pages, the 2473-20 operator’s manual, the 2573-20 parts list and the 2026 compatibility matrix, read Oct 20, 2026.
  • The kit, the bare tool and the jaw are listed as one kit with no shared score, because a jaw does a different job from a tool. Within one model family, a score would only repeat the specs anyway.
  • Listings with “for Milwaukee” titles or long lead times left out.
  • CPSC recall search for Milwaukee: no press tool, jaw or M12 pack recalls.

Sources

  • Milwaukee 2473-20 product page (replaced by 2573-20; box contents; 5,400 lbs; 32,000 crimps; 1-1/4 in. jaw 49-16-2453; 5-year tool, 2-year battery, charger and jaw warranty): milwaukeetool.com, read Oct 20, 2026.
  • Milwaukee 2473-22 product page (replaced by 2573-22; kit contents; 3.8 lbs; 30-minute recharge; all M12 batteries): milwaukeetool.com, read Oct 20, 2026.
  • Milwaukee 2573-20 product page and FAQ (box contents, 37,000 cycles, Auto-Cycle, prepress battery check, ONE-KEY, sizes, jaw locking, warranty): milwaukeetool.com, read Oct 20, 2026.
  • Milwaukee 2573-22 product page (kit jaws 49-16-2450, 2451, 2452; 2-year jaw warranty; specs tab): milwaukeetool.com, read Oct 20, 2026.
  • Milwaukee M12 press tool 2473-20 operator’s manual 58-14-2490d2 (press steps, fuel gauge, LED troubleshooting, 30/15-minute rule, head change, maintenance, cleaning, limited warranty).
  • Milwaukee 2573-20 service parts list PN0003467, May 2026 (CR2032 coin cell, FCC ID, Packout case 48-22-8450, service contacts).
  • Milwaukee 2026 Press Tool Compatibility Matrix, M12 column (fitting systems, jaws and rings, RIDGID jaw part numbers, installer rules): milwaukeetool.com, read Oct 20, 2026.
  • Amazon product listings for B009G48D3M, B009G48CTM and B00A0ZK7TO, read October 27, 2026.
  • Milwaukee limited warranty, PN 00-01641 (power tool warranty to the original purchaser from an authorized Milwaukee distributor): documents.milwaukeetool.com, read October 27, 2026.
  • CPSC recall database (saferproducts.gov) searched for Milwaukee: Oct 20, 2026, 7:34 AM EDT.

Related guides